1)Anchoring Structure锁紧结构
英文短句/例句
1.Experimental Research on Lockup Structure of External Friction Based Medical Robot Joint基于外摩擦的医疗机器人关节锁紧结构实验研究
2.retaining mechanism锁紧[制动]机构，保持机构
3.reverse anchor jam nut反向锁闭机构紧固螺帽
4.THE STRUCTURAL ANALYSIS OF THREAD LOCKED HEAT EXCHANGERS AND DIAPHRAGM HEAT EXCHANGERS螺纹锁紧环换热器与隔膜密封换热器的结构分析
5.Electromagnetic locking device based on self-locking for magnetic suspended flywheel基于自锁原理的磁悬浮飞轮电磁锁紧机构
6.Optimal Design for Locking Mechanism of Bundling Machine Based on ADAMS基于ADAMS的捆扎机锁紧机构的优化设计
7.A group of related and closely linked structural genes, together with the operator gene that controls their expression are collectively called an operon.一组相关的、紧密连锁的结构基因加上控制其表现的操纵基因，统称操纵子。
8.of such close construction as to be impermeable.结构紧密以至不透水的。
9.The structure of Liu's calligraphy is tight in the middle and loose on the four sides.结构中宫收紧，四维开放，
10.Analysis and Design of RF Oscillator and PLL Architecture;射频振荡器与锁相环结构分析与设计
11.Observation of Microstructure of Follicular Atresia of Northeast Sika Deer (Cervus nippon)东北梅花鹿卵泡闭锁的显微结构观察
12.A Latch-up in Bipolar Circuit一种Bipolar结构中的闩锁效应
13.Development of Molecular Markers Linked to the Nematodes Resistance "N" Gene in Pepper;与辣椒抗根结线虫N基因紧密连锁AFLP标记的开发
14.The Structure and Displacement Analyses about the Atresia Mechanism of the Subway Screen;GFMA3744地铁隔断门闭锁机构结构和位移行程分析
15.Network type microcomputer-based anti-misoperation locking system based on large-scale network structure and locking in the partition基于大网络结构+间隔内闭锁设计思想的网络型微机防误闭锁系统
16.The atoms themselves are firmly held in place in the crystal structure of a metal.原子本身被紧紧束缚在金属的晶体结构之中。
17.GLOBAL DEFLATION TENDENCY AND CHINESE STRUCTURAL DEFLATION;世界通货紧缩趋势与中国的结构性通货紧缩
18.The Comprehension of Chinese Spoken Idioms with Fixed and Unfixed Structure结构紧密与不紧密的汉语口语习语的理解
相关短句/例句
cone lock牙轮锁紧结构
3)locking mechanism锁紧机构
1.The structure traits of the abroad successful locking mechanism of gauge-changeable wheelsets were introduced,the key technology of locking mechanism was analyzed.介绍了国外成熟变轨距轮对锁紧机构的结构特点,分析了锁紧机构设计的关键技术。
2.Locking mechanism of dumping body tailboard is one of the key problems in designing dump trucks.车厢后板锁紧机构的设计是自卸汽车设计中主要解决的问题。
3.The locking mechanism of bundling machine was studied.以锁紧机构为研究对象,通过理论计算分析影响锁紧力的因素,在ADAMS软件中对锁紧机构各主要杆件进行参数化,创建锁紧机构的虚拟样机优化模型;以锁紧力最大为目标,对模型各设计变量进行分析,找出了对目标影响最大的变量,通过优化确定模型的最佳结构;最后将导入钢扣柔性体导入虚拟样机模型,比较优化前后的锁紧机的性能。
4)lock and unlock mechanism锁紧与解锁机构
5)Hold-down and release mechanismboom锁(压)紧释放机构收拢结构
6)lock bottom structure锁底结构
1.This paper discusses the reason and harm of incomplete penetration rounded welded root of titanium alloy cabin with lock bottom structure in air-to-air missile,and presents several solutions of this problem.对空空导弹钛合金舱体插接锁底结构圆周焊缝根部未焊透的产生原因和危害进行了讨论,提出了几套解决和防止根部未焊透缺陷的工艺方案。
延伸阅读
抽芯成型高差大的滑块多级锁紧结构在压铸模设计中, 常常会遇到同一抽芯而各成型高度相差较大的零件, 如果采用斜拉杆或弯销抽芯, 习惯上采取的措施是增加滑块的高度,以满足滑块的退位空间,其结果是滑块的重量增加,模框的强度降低。 图1 是汽车油泵调速器前壳压铸件示意图, Ⅰ- Ⅰ分型面需用抽芯才能完成脱模,其最低抽芯高度Hmin 为17mm, 最大抽芯高度Hmax为45mm, 为了保证滑块有足够的退位空间而不发生自锁, 滑块的高度必须大于或等于45mm。为避免抽芯距离过大造成滑块体积增加, 在设计中采用了局部增高多级锁紧结构,如图2 所示。P 是高于17mm低于45mm的面,N是高于45mm的面,M面是与N面同高且保证N 面受力平衡的辅助结构。α为抽芯角,β1 、β2 为锁紧角,β1 、β2 不仅具有锁紧作用,而且在开模抽芯时还具有让位的作用,所以β1 、β2 必须大于α, 而且β2 应大于β1 , 否则开模时, 滑块会出现自锁。锁紧角β2 也可以等于β1 , 但由于制造时有误差, 如果误差大, 则β1和β2 形成的锁紧面会出现干涉。在压铸件调速器前壳模具设计中, α取23°, β1 取26°, β2取30°,实现了安全生产。总之, 对于那些抽芯高度相差大的滑块,采用多级锁紧结构,对减小滑块的重量、延长模具寿命,节约模具材料具有重要的作用。
