1)Shell thickness坯壳厚度
1.The solidified shell thickness of Jigang slab caster is measured by nail-shooting technology,and the measuring results are compared with theoretical calculation values.采用射钉法测量济钢大板坯连铸机坯壳厚度,将实测结果与理论计算的结果进行对比,修正了综合凝固系数,指导改造了二冷喷嘴的结构,加强了铸坯冷却强度,年铸坯产量达225万t。
2.The application of nail-shooting technique in the shell thickness measuring was introduced.介绍了射钉法在测量连铸坯凝固坯壳厚度方面的应用情况。
3.Unsteady temperature distribution and shell thickness in the continuous casting bloom were numerically simulated.利用数值模拟手段计算连铸方坯中非稳态温度场分布及坯壳厚度,根据所需的凝固分率所对应的坯壳厚度点来预报轻压下设备的轻压下位置。
英文短句/例句
1.Measurement of the Solidified Shell Thickness in the Secondary Cooling Zone of Continuous Casting of Bloom大方坯连铸二冷区凝固坯壳厚度测试
2.Study on Solidified Shell Thickness Measurement and the Solidified Shell Shape of Slab连铸板坯坯壳厚度测定及凝固壳形貌模拟研究
3.Minimum Mould Exit Shell Thickness of Round Blooms for Peritectic Steel Casting包晶钢圆坯结晶器出口安全坯壳厚度的研究
4.Study on the Shell Thickness Variation and Liquid Core Position for Bearing Steel Bloom轴承钢铸坯凝固坯壳厚度变化及液相穴位置测定研究
5.Molten steel leakage by binding has the defects including disordered vibration mark on outer surface of surviving billet shell, thickness of billet shell gradually getting thinner from up to down and large uneven coefficient of billet shell thickness.粘结漏钢具有残留坯壳外表面振痕紊乱、壳厚度从上向下逐渐变薄和坯壳厚度不均匀系数大的特点。
6.Discussion about Calculating Mode of Solidifying-skull's Thickness in Jinan Steel's Slab CCM济钢板坯铸机凝固壳厚度计算模型的探讨
7.Slab: rectangular in cross-section, with rounded corners and more than 5cm in thickness.大板坯--横断面为矩形，圆角，厚度在5cm上。
8.Development and Application of 330 mm Slab Casting Technology330mm厚度连铸坯技术的开发与应用
9.Numerical Simulation for Temperature Distribution of Initial Solidifying Shell with Mold Tube During Bloom Casting of U71Mn SteelU71Mn大方坯凝固坯壳与结晶器铜管温度场的数值模拟
10.Study on Curve of Pressure-thickness of MDF Mat and Its Application中纤板压力-板坯厚度曲线的研究与应用探讨
11.Influence of Oxide Skin Thickness on Photoemissivity of Polarizing Angle from Surface of Continuous Casting Billets氧化层厚度对铸坯表面偏振角发射率的影响
12.Billet Surface Temperature Measuring in the Thick Board Factory of Jinan Steel Group钢坯表面温度检测系统在济钢中厚板厂的使用
13.However, the crust is almost four times thicker than the earth's crust.然而，月球地壳几乎是地球地壳厚度的四倍。
14.INVERTION OF CRUSTAL THICKNESS OF MOON FROM GRAVITY FIELD AND TOPOGRAPHY DATA利用重力场和地形数据反演月壳厚度
15.The continental crust is much thicker than average beneath the great mountain belts.在高山地带下面的大陆地壳，其厚度要比平均厚度大得多。
16.A device to thicken edge of pre-punching hole on blank is also developed.还研制了在板坯的预冲孔上增加边缘厚度用装置。
17.Steps were made on the female die surface to make up for the thickness different of the blanks.凹模表面和型腔加工了台阶以补偿坯料的厚度差值。
18.Numerical Simulation of Temperature Field and Stress Field for and Axial Crack Analysis of Heavy-wall Centrifugally Cast Hollow Bloom厚壁离心管坯温度场和热应力场的数值模拟及其轴向裂纹分析
相关短句/例句
solidified shell thickness坯壳厚度
1.Determination of solidified shell thickness of continuous casting slab at Angang;鞍钢厚板坯凝固坯壳厚度的测定
2.The surface temperature and the solidified shell thickness of round billet are strongly influ.由于拉速变化引起计算空间内质量流量的变化,圆坯的表面温度和坯壳厚度受拉速强烈影响。
3.The solidified shell thickness and solidification coefficient of slab in the secondary cooling zone on Pangang curved slab caster have been studied,by use of “pin shoot”method.研究工作运用“射钉法”,准确地标定了攀钢弧形板坯连铸机二冷区凝固坯壳厚度及凝固系数 ,为评价现有二冷系统的冷却能力、制定合理的二冷配水制度和高拉速条件下的工艺参数提供了重要依据。
3)minimum mould exit shell thickness安全坯壳厚度
1.The value of the minimum mould exit shell thickness(MEST)is one of key factors to consider for continuous casting machine design and the strand cooling schemes.结晶器出口的安全坯壳厚度确定一直是连铸设备与工艺设计中十分关注的问题。
4)solidified shell thinkness凝固坯壳厚度
5)Parison thicliness型坯厚度
6)paper thinkness纸坯厚度
1.Application of laser displacement sensor in the paper thinkness on-line measurement;激光位移传感器在纸坯厚度在线检测中的应用
延伸阅读
实坯坯1.见"实丕丕"。
