1)prebaked cell预焙槽
1.The theoretical calculation of the electrolyte temperature variation rule and heat loss during pole changing of 240kA prebaked cell was represented.阐述240kA预焙槽换极过程的电解质温度变化规律及对热损失的理论计算。
2.After the 80kA self-baking anode was replaced by the prebaked cell, the primary wet cleaning system was reserved, but the running had shown that the smoke dust discharge concentration was over proofed and the system breakdown frequently.80kA侧插自焙槽改为预焙槽后 ,保留原有湿法净化系统 ,运行后发现 ,烟尘排放浓度超标 ,系统故障频繁。
英文短句/例句
1.The Development and Application of High-temperature Fume Preheating Technology on the 75kA Aluminum Reduction Cell;高温烟气焙烧技术在75kA预焙槽上的开发应用
2.TECHNICAL AND ECONOMIC ANALYSIS OF THE CONVERSION FROM SODERBERG CELLS INTO THE CENTER POINT FEEDING PREBAKED CELLS IN THE SAME CAPACITY;自焙槽改造为同级中间点式下料预焙槽的技术经济分析
3.Optimized model and template for anode exchange sequence of prebaked anode cell预焙槽阳极更换顺序表的优选模型和模板
4.open prebaked anode type cell敞开式预焙阳极电解槽
5.Study on the Life of GL 190kA Prebaked Aluminum Reduction Cells;GL190kA预焙铝电解槽槽寿命问题研究
6.Technique code for retrofitting soderberg cell into prebaked anode cell in aluminium smelters自焙阳极铝电解槽预焙化改造技术规范
7.In-depth Characteristics Extraction of Cell Voltage Fluctuation in Aluminum Reduction Cells大型预焙铝电解槽槽电压波动特征提取
8.Spectral analysis of cell voltage fluctuation in 320 kA pre-baked aluminum reduction cells320kA系列预焙铝电解槽槽电压波动的频谱解析
9.Experimental Application of Pre-baked Slot Anode in 300 kA Aluminum Smelting Pot预焙沟槽阳极在300kA铝电解槽上的试验与应用
10.The Research of Fault Diagnosis System for 350kA Pre-baked Aluminum Reduction Cell;350kA预焙铝电解槽故障诊断系统的研究
11.The Study of the Enlarge of Current in 160KA Cell;160KA预焙铝电解槽强化电流试验研究
12.The Simulation of the Flow Field of 300kA Large Scale Prebaked Aluminum Electrolysis Cell300kA预焙阳极铝电解槽流场的仿真
13.Energy Saving Operation of 300 kA Prebaked Aluminum Smelting Pot300kA预焙铝电解槽节能生产经验
14.Discussion on the technology of increasing the current of large prebaked cell大型预焙铝电解槽强化电流技术探讨
15.The controller is applied to realize the control of pre-baked aluminium electrolytic cell temperature.利用该控制器实现对预焙铝电解槽的温度控制。
16.Study on Design and Optimization of the Electric-Magnetic Field of Large Prebaked Aluminum Reduction Cells;大型预焙铝电解槽电磁场设计与优化研究
17.The Simulation of the Thermal-electric Field of Large Prebaked Aluminum Reduction Cell Based on ANSYS;基于ANSYS的大型预焙铝电解槽热电场的仿真
18.The Research on Optimize of Large Pre-baked Anode Cell Process Technical Conditions;大型预焙铝电解槽工艺技术条件优化试验
相关短句/例句
pre-baked anode cell预焙槽
1.Analyzing CA distance of large pre-baked anode cell;大型预焙槽阳极极距分析
2.The paper sets up optimized model for anode exchange sequence of pre-baked anode cell by means of application template designed with usual office software.利用常用办公软件设计了应用模板,建立了预焙槽阳极更换顺序的产生及优选模型,并使用该模板排出了合理的换极顺序。
3)pre-baked cell预焙槽
1.As the aluminum industry facing the strictly environment claim and the drastic market competition, it is very important to reconstruct of self-baking cell replaced cell by the original pre-baked cell.利用预焙槽实施对自焙槽的改造有以下两种方式:一是保留电解厂房,整流所容量扩大,用大型现代化预焙槽取代小型自焙槽;保留原有自焙槽系列大部分设施如整流所、电解厂房、槽壳等,改造成同级的小型预焙槽。
2.The practical experience of the first 280 kA pre-baked cell which reduced anode effect coefficient in our country was comprehensively summarized in this paper.总结了我国第一条280 kA预焙槽生产系列降低阳极效应系数的生产实践经验,提出现场浓度和原材料质量控制是有效降低阳极效应系数的保证,同时深入分析了提高效应管理的途径,指出新时期加强效应管理的重要性和迫切性,认为国内铝行业在效应管理方面赶上世界先进水平是可以实现的。
4)135kA pre-baked anode reduction cell135kA预焙槽
1.Practices of prolonging the service life of 135kA pre-baked anode reduction cell;根据135kA预焙阳极电解槽的生产实践,提出了采用合理的焙烧方法,控制135kA预焙槽长期低温平稳运行、小炉膛生产的措施,在电流效率提高的同时达到延长槽寿命的目标。
5)kA prebaked cell85kA预焙槽
1.Application of an advanced technology to 85kA prebaked cell and its optimization;“四低一高”工艺在85kA预焙槽的应用与优化
6)kA Prebaking cell186kA预焙槽
1.Industrial Experiment for Dry Permiation-proof Material Used in 186kA Prebaking cell;云南铝业股份有限公司186kA预焙槽干防渗料工业试验
延伸阅读
焙造1.烘制。
