1)mold with hybrid magnetic fields组合式结晶器
英文短句/例句
1.Formation of Subcutaneous Blow Hole of Casting Slab With Composite Mould组合式结晶器内连铸坯皮下气泡的形成
2.The reduction of noise amorphous alloy core padmounted transformers非晶合金铁心组合式变压器噪声的降低
3.A combined micro-gripper with high resolution and large working space is developed which integrates the linear micro motor and bimorph cantilever structure.将微直线电机宏动机构与双晶片压电悬梁微动机构结合,研制高精度、范围的组合式微夹持器。
4.vertical straight-mould machine立式直结晶器连铸机
5.Preparation of basic magnesium sulfate whiskers by rotor-stator reactor and hydrothermal method定-转子反应器结合水热法制备碱式硫酸镁晶须
6.Structural Study and Design of Build-up Pig with Flexible Shaft柔轴组合式清管器的结构研究与设计
7.Microstructure of Surface Recrystallization of Single Crystal Superalloy DD6单晶高温合金DD6表面再结晶组织
8.Numerical Simulation and Structure Optimization of a Combined Liquid-Solid Distributor;组合式液固分布器的数值模拟和结构优化
9.Microstructure of Cu-Ti-Zr-Ni Bulk Amorphous AlloyCu-Ti-Zr-Ni块体非晶合金的结晶组织分析
10.(chemistry) variability in chemical composition without variation in crystalline form.结晶形式不变而化学组成改变的现象。
11.Research of ccm mould no -sin vibration mode连铸机结晶器非正弦振动模式的研究
12.Mathematical model of cantilever type crystal CMM悬臂式结晶器坐标测量机的数学模型
13.Study on Non-sinosoidal Oscillation System by Electrical Drive for Continuous Casting Mold连铸机结晶器电动式非正弦振动研究
14.Synthesis and Crystal Structure of N-Benzenesulfonyl-Histidine;苯磺酰组氨酸的合成及晶体结构研究
15.Dynamic Recrystallization Behavior and Microstructure Evolution of Cu-Ni-Si-Cr AlloyCu-Ni-Si-Cr合金动态再结晶及组织演变
16.Age-hardening mechanism of Cu-Co-Be alloy for industrial crystallizer工业结晶器用Cu-Co-Be合金时效强化机制
17.Application of 110kV amorphous alloy dry type transformer110kV干式非晶合金变压器的应用
18.STUDY ON THE GEOMETRY OF SUBMERGED ENTRY NOZZLE FOR BLOOM CASTING大方坯连铸结晶器浸入式水口结构研究
相关短句/例句
built up mold组合模;组合式结晶器
3)mould assembly组合结晶器
1.The results showed that the molten steel enters into the mould assembly in three flows of which the two move upward peripherally at the same time to form symmetrically two eddies at the upper part of the mould,while the other one moves downward peripherally and,eventually,g.采用湍流两方程模型,对连续铸造复合轧辊组合结晶器内钢液的流场进行了数值模拟研究,分析了拉坯速度及浇注倾角等工艺参数对组合结晶器内钢液流场的影响。
4)build-up mould组合式铜板结晶器
5)mold with hybrid magnetic field复合式结晶器
1.The flow field in a new mold with hybrid magnetic fields with combination of alternative and static electromagnetic fields for continuous casting was simulated.采用数值模拟方法分析了电磁连铸复合式结晶器内的流场。
6)combination resultant组合结式
延伸阅读
组合式结晶器compositemold：由四块壁板组成，每块壁板又由一块铜板和一块钢（铁）板用螺栓连接而成。
