串行口,serial port英语短句,例句大全

串行口,serial port
1)serial port串行口
1.The IP-Core Design of MCS-51 S Serial Port;MCS-51单片机串行口IP核的实现
2.Application of the program for the serial port and the onboard port based on CB;基于CB的串行口和接口板端口程序应用
3.Introduces microcomputers communication with single-chip microcomputer serial port,a method of a lots of Neon lamp colors compute scanning controller running with synchronous is discussed.介绍了一种利用单片机串行口的多机通讯功能,实现多台微电脑霓虹灯全彩扫描器同步运行的方法,给出了系统的硬件结构和软件设计的思路。

英文短句/例句

1.Universal Serial Bus (USB) is similar to a serial port.通用串行总线（USB）与串行口相似。
2.Research of Communication Between Serial and Ethernet Ports Based on C8051F340基于C8051F340串行口到以太网口转换的研究
3.Application of the program for the serial port and the onboard port based on CB基于CB的串行口和接口板端口程序应用
4.There are no Serial Ports which can be setup on this system.在这个系统上没有可以安装的串行口。
5.Capabilities and management of the serial port, logical device.串行口、逻辑设备的功能和管理。
6.MCS Serial Port Baud-Rate Designed with Program用编程方法实现单片机串行口波特率
7.An ESSP Circuit Design in 16 Bits High Speed DSP;16位高速DSP增强型同步串行口的设计
8.Application of CD4052 as Mul-series Expander;应用CD4052扩展单片机串行口
9.Interface of Serial Communication Programming in Win32;32位视窗系统串行通讯的串口设置
10.Realization of Serial Communication Using MOXA Multi-serial-port Card Based on VC++VC++中基于MOXA多串口卡串行通信的实现
11.Command-line error: Invalid port for serial port mapping.命令行错误: 串行端口映射的端口无效。
12.Command-line error: Invalid file for serial port mapping.命令行错误: 串行端口映射的文件无效。
13.Connect using my serial, parallel, or infrared port.使用我的串行、并行或红外端口连接。
14.APPLICATONS OF SERIES COMMUNICATION INTERFACE TO 16 DIGITS MICRO-COMPUTER串行通信接口在16位微机中的应用
15.CAMAC-Serial highway interface systemsGB/T7522-1987CAMAC串行信息公路接口系统
16.Select the com port to which you connected the settop serial cable and click next选择com端口连接SETTOP串行电缆，单击 Next
17.Design of Two CMOS Serial Communication Interface Chips;两种CMOS串行通信接口芯片的设计
18.Research and Implementation on High Speed Serial Interfaces in Beyond3G System;B3G系统中高速串行接口的研究与实现

相关短句/例句

serial interface串行口
1.According to the working principles of serial interface of 8051 one-chip computer,this paper puts forward the method of adjusting the needed bps by programming,that is time-delay method.本文根据8051单片机串行口的工作原理,提出通过编程调整所需波特率的方法———延时法。
2.The text introduces the working principle of microcomputer s serial interface and parallel interface,application in correspondence and programming way.介绍微机串行口和并行口的工作原理 ,在通信方面的应用及有关编程方
3)serial interface串行接口
1.Study on the communication scheme of signal modulation and demodulation based on serial interface;基于串行接口信号调制/解调的通信方案研究
2.PCB of micro controller serial interface for experiment;单片机串行接口实验电路板的设计
4)serial port串行接口
1.RS—485 Serial Port and Industrial Control Local Area Network;RS—485串行接口及其构成的工业测控网络
2.Using a low-power CMOS 8-bit microcontroller ATmega8,ten-bit digital signals realizes analog-to digital conversion,and the converted signals are transmitted into the PC by RS232 serial port.介绍了网上心电实时监护系统,应用ATmega8型8位微处理器芯片实现了10位精度的心电AD转换,通过RS232串行接口向PC机传送数据,并介绍这2部分的软、硬件设计思想。
3.This paper introduces a design scheme of a serial port communication technology based on embedded gateway.介绍了一种基于嵌入式网关的串行接口通讯的设计方案。
5)series interface串行接口
1.Integrated TTS processor SD178A and its series interface;SD178A型集成式TTS处理器及其串行接口
2.The characteristics of thesystem ,the series interface circuits and the useful anti-interference methods used in thesystem have been analysed.本文介绍一种网络结构的微机实时监测系统，分析了系统的特点、串行接口电路和有效抗干扰措施。
3.This paper designs a series interface between ARPA (JAS-800 for example) and speech output system.本文以JAS-800为例设计出语音输出系统与ARPA间的串行接口,使之从ARPA中的引出线减少到10根。
6)serial port串行端口
1.VB programming on PC serial port;PC机串行端口的VB编程
2.The Analysis of the Current Inevitability about Serial Port P1394 Substituting for USB;当前串行端口P1394取代USB的必然性分析
3.This paper discusses the method of realizing communication of computer serial port by MScomm control of VB, which makes communication successful in stand-alones, and between a stand-alone and a computer, capturing the misinformation during communication by adaping OnComm event.利用VB中MScomm控件实现计算机串行端口通信,该方法实现了单机之间、计算机与计算机之间以及单片机与计算机之间的通信,并能利用OnComm事件捕获通信期间的错误信息。