C/C复合膜,C/C composite membrane英语短句,例句大全

C/C复合膜,C/C composite membrane
1)C/C composite membraneC/C复合膜
1.The membranes were served as the support of C/C composite membranes for gas separation,applied in the treatment of TiO2 wastewater and oily wastewater.结果表明:以煤基管状炭膜为支撑体,分别以聚醚砜酮(PPESK)和聚糠醇(PFA)为前体,采用浸渍涂膜法制备的气体分离用C/C复合膜,在25℃时H2/N2,O2/N2,CO2/N2的分离系数分别为104。

英文短句/例句

1.Investigation on Gas Separation Performance of Coal-base Tubular C/C Composite Membrane Prepared by Template Method;模板法制备煤基管状C/C复合膜气体分离性能的研究
2.ANTI-WEAR PROPERTIES OF WS_2/MoS_2/C COMPOSITE FILMSWS_2/MoS_2/C复合薄膜的磨损性能研究
3.Preparation of C-P-CA Composite Film and Researches as Oral Ulcer Treatment Biomaterials;C-P-CA复合膜作为口腔溃疡治疗材料的研究
4.Preparation of PEDOT:PSS-C composite film counter electrode on the flexible substrate柔性基底上PEDOT:PSS-C复合薄膜对电极的制备
5.Comparative study of friction and wear behavior of C/C/Cu and C/Cu compositesC/C/Cu及C/Cu复合材料摩擦磨损行为比较
6.Property Research of C/C-SiC Composite;C/C-SiC复合材料的性能研究
7.Study on the Performance of C/C Composites Used as Rolling Seal;动密封用C/C复合材料性能的研究
8.Study on Microstructures and Fine Structures of the Carbon/Carbon Composites;C/C复合材料的显微和精细结构研究
9.HOT PRESSING JOINING OF CARBON/CARBON COMPOSITES TO METALC/C复合材料与金属材料的热压连接
10.Electrical sliding wear behavior of C/C-Cu compositesC/C-Cu复合材料的载流摩擦磨损行为
11.Analysis of the Microstructure of C/C Composite by CTC/C复合材料微观结构的CT分析
12.Microwave assisted chemical vapor infiltration to prepare carbon/carbon composites微波热解CVI法制备C/C复合材料
13.ARC EROSION PROPERTY OF C/C COMPOSITES WITH ELECTRIC CURRENTC/C复合材料抗电弧侵蚀性能研究
14.Influence of Precursors on Preparation of C/C Composites by CVI前驱体对CVI制备C/C复合材料的影响
15.ANALYSIS FOR CRACK OF C/C COMPOSITES PREPARED BY TG-CVITG-CVI C/C复合材料裂纹缺陷成因分析
16.Spectral Emittance Measurement of C/C CompositeC/C复合材料光谱发射率测量研究
17.Preparation of Anti-ablation HfC Coating on C/C Composite MaterialC/C复合材料抗烧蚀HfC涂层的制备
18.Development of Al_2O_3-ZrB_2-C Composite;Al_2O_3-ZrB_2-C质复合材料的

相关短句/例句

C/C-compositeC/C复合
3)WS2/MoS2/C Composite FilmsWS2/MoS2/C复合薄膜
4)compound A/C axe复合A/C轴
1.Second-order sliding mode control for permanent-magnet ring torque motor used in compound A/C axe;复合A/C轴永磁环形力矩电机二阶滑模控制
2.The compound A/C axe direct drive ring permanent magnet torque motor servo system in high precision five axes gang numerical control machine is easily affected by the load disturbance and parameter variation,and rapid tracking performance and precision are influenced by the coupling between machine and electric variables.针对高精度五轴联动数控机床中主轴头复合A/C轴直接驱动环形永磁力矩电机伺服系统易受负载扰动和参数变化影响的特点,以及其机械和电气变量间的耦合影响速度跟踪的快速性和精度的问题,设计了基于奇异摄动理论的二阶滑模鲁棒速度控制器。
3.For the characteristics of compound A/C axe direct drive permanent magnet ring torque motor servo system in high precision five axes module numerical control machine suffering from varying of load and variables,the position controller is proposed by using discrete time second order sliding mode.针对高精度五轴联动数控机床中主轴头复合A/C轴直接驱动永磁环形力矩电机伺服系统易受负载扰动和参数变化影响的特点,采用离散二阶滑模设计了位置控制器。
5)carbon/carbon compositesC/C复合材料
1.Effect of Si/Mo ratio on microstructure and high-temperature antioxidation property of SiC-MoSi_2 coating for carbon/carbon composites;硅钼含量对C/C复合材料SiC-MoSi_2涂层结构和高温抗氧化性能的影响
2.The ablation performances of two kinds of carbon/carbon composites with different pyrocarbon were investigated on a high-pressure arc heater.采用电弧驻点烧蚀试验方法测试了具有典型光滑层和粗糙层热解炭结构的两种C/C复合材料的烧蚀率,研究了热解炭结构对C/C复合材料烧蚀性能的影响。
3.The advantage of carbon/carbon composites is constrained by its oxidation at high temperature.C/C复合材料高温氧化性限制了其在高温领域的更广泛应用。
6)C/C compositesC/C复合材料
1.Ablation characteristics of 2D-C/C composites and their graphitized products;2D-C/C复合材料及其石墨化制品烧蚀特性分析
2.Effects of graphitization degree and fiber content on properties of C/C composites;石墨化度及纤维含量对C/C复合材料性能的影响
3.Effect of content and type of matrix carbon on sliding tribology behavior of C/C composites;基体炭含量对C/C复合材料滑动摩擦磨损行为的影响