1)bore dimension,bore size内径尺寸
英文短句/例句
1.Rubber and plastics hoses--Bore diameters and tolerances on lengthGB/T9575-1988橡胶、塑料软管内径尺寸和长度公差
2.The Method for Measuring Diameter Size of Ring with Universal Measuring Microscope用万能工具显微镜测量环规内径尺寸的方法
3.BORE AND STROKEThe size of an engine cylinder is referred to in terms of the Bore and stroke.内径和行程:发动机气缸的尺寸与内径和行程有关。
4.Broe gauges are used to measure internal hole dimensios and shape errors of different diameter and depth by comparative method.内径百分表适用于比较法测量不同直径和深度和内孔尺寸及误差。
5."R.Radius, represents curve dimension."半径,表示曲线尺寸
6.Malleable cast iron pipe fittings--Type size--Reducing inner joints(nipples hexagon)GB/T3289.27-1982可锻铸铁管路连接件型式尺寸异径内接头
7.Malleable cast iron pipe fittings--Type size--Male and female reducing teesGB/T3289.11-1982可锻铸铁管路连接件型式尺寸异径内外丝三通
8.Malleable cast iron pipe fittings--Type size--Male and female reducing elbowsGB/T3289.5-1982可锻铸铁管路连接件型式尺寸异径内外丝弯头
9.sizematic internal grinder自动定尺寸内圆磨床
10.the rate of increase in size per unit time.单位时间内尺寸增加率。
11.Use to add an angular dimension with dimension arrows that point inward.用于添加指向内部的尺寸箭头的角度尺寸。
12."The pin gauges are used to measure the whole distance, the pitch diameter of the thread, etc. Especially, they are suitable for curved groove width measurement."针规适用于机械加工中孔径、孔距、内螺纹小径的测量,特别适于弯曲槽宽及模具尺寸的测量。
13.Flat belt drive pulleys diametersGB/T11358-1989平带传动带轮直径尺寸
14.Radial turbocharger--Connection dimensionsGB/T9485-1988径流式涡轮增压器连接尺寸
15.large sapling大幼树(高10英尺以上, 胸径4英寸以下)
16.Study on Grain Refinement of Aluminum Rod of Large-Size Processed by Equal Channel Angular Pressing;等径角挤压法细化大尺寸铝棒材晶粒尺寸的研究
17.Before lighting the fuse, the hole was topped off with sand, and a three-foot-long, 1.25" diameter iron tamping rod was used to pack down the gunpowder.在点燃之前，洞的上部填满了黄沙和一根长3英尺，直径1.25寸的内置火药的铁棒。
18.The outside diameter of copper tube shall be tested by Micrometer. The tooth depth and the bottom wall thickness shall be tested by Microscope.外径尺寸用外径千分尺测量.齿高和底壁厚用双目倒置小金相测量。
相关短句/例句
Inner and Outer Dimension内外径尺寸
3)bore size孔尺寸，内径
4)in the clear内尺寸，内径，内宽
5)ID (①inside ②inside dimensions)①内径 ②内部尺寸
6)aperture size孔径尺寸
1.From the basic concept of the materialist dialectics,and the relations between the types and properties of pores within the concrete,the rule in which the aperture size of concrete acts on the durability of the concrete was explored.探索了混凝土孔径尺寸影响混凝土耐久性的作用规律,提出混凝土孔隙半径与使用寿命关系的数学模型和修正系数。
2.On the basis of the Darcy formula and the Cantor equation, the impact of the aperture size of concrete to its impermeability was discussed.根据Darcy公式和Cantor方程,研究了混凝土孔径尺寸对其抗渗性的影响。
延伸阅读
工程图标准尺寸及坐标尺寸标准标注类型，是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。· 3.2 标准标注到坐标标注的转换注意： 转化为坐标标注的尺寸必须是线性标注的，下列尺寸不能转化为坐标标注： 被显示成线性尺寸的直径 中心线尺寸
- 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base. 选择作为参考基准线的尺寸 选择基准的引出线，该点为0点 选择 MOD DIM TYPE > Lin to Ord . 选择线性尺寸：注意：必须选择具有相同基准的尺寸
