偏心矩,eccentricity
1)eccentricity[英][,eksen'tr?s?ti][美]['?ks?n'tr?s?t?]偏心矩
1.The paper introduces three methods of calculation of eccentricity for vibratory roller s semicircleeccentric block, compares the three results of calculation with example.介绍了振动压路机半圆形偏心块偏心矩的3种计算方法,并利用设计实例对这3种方法的计算结果进行了比较,计算误差在1%以内,并推荐使用三维软件的设计方法。
2.The accuracy of eccentricity is 0.3%,偏心矩测量精度0。
英文短句/例句

1.Discussion on the Computational Methods of Eccentricity Magnification Coefficient of Eccentric Compression Reinforced Concrete Members钢筋混凝土偏压构件偏心矩增大系数计算方法探讨
2.Analysis of Disturbing Torque in Electrostatic Field Caused by Rotor Radial Disbalance in ESG静电陀螺转子径向偏心干扰力矩分析
3.Discussion about"Analysis of Correlation Curves between the Axial Force of Eccentrically Pressed Member with Rectangular Cross Section and the Bending Force Moment;关于“矩形截面偏心受压构件轴力——弯矩相关曲线分析”的探讨
4.The limit of dimension eccentric compression under the situation of rectangle asymmetric reinforcement矩形截面不对称配筋下大小偏心受压的界限
5.Research on Loading Capacity of Short Column Made of Concrete-Filled Rectangular Steel-Tube under Eccentric Compression偏心受压矩形钢管混凝土短柱承载力研究
6.Research on Motion Character of Two-axle Vibrating Screen with Same Mass Moment and Mass Center Deviated Vibrator质心偏移式等质量矩双轴振动筛运动特性研究
7.The Influence of Pre-eccentricity of Single-Pier Support on Torsion Re-distribution of Continuous Curved Bridges支座预偏心对独柱曲线连续梁桥扭矩重分布的影响
8.moment due to elevator deflection偏转升降舵产生的力矩
9."Torque is calculated by multiplying the push by the crank offset, or the distance of the push from the rotating shaft,"扭矩以推力与曲柄偏心距或旋转轴心至推力作用点的距离相乘计算。
10.eccentric sheave偏心内轮偏心皮带轮
11.The Test and Theory Study in the In-Plane Stability Capacity of Hot-rolled H-section Columns under Eccentric Load;热轧H型钢偏心受压构件在弯矩作用平面内极限承载力的理论与试验研究
12.be biased in favor of a person对某人有偏心 [偏爱]
13.Partial Ordering of Generalized Inverse and the Solution of the Equation of Matrix Polynomial Function;矩阵广义逆偏序与矩阵多项式函数方程解
14.The distance between the center of an eccentric and its axis.偏心距偏心圆的中心与圆轴间的距离
15.The Structure Design of Magnetic Suspension Momentum Wheel with Deflection Angular Momentum;动量矩可偏置磁悬浮动量轮结构设计
16.The Spectram of Hamiltonian Operator Matrics Corresponding to Partial Differential Equation由偏微分方程导出的Hamilton算子矩阵的谱
17.Analysis of Double Plate Rotation Depolarizer by Mueller Matrix双光楔旋光退偏器的Mueller矩阵分析
18.Reason for the Greater Tilting Moment of a 220 t Converter220t转炉倾动力矩偏大的原因分析
相关短句/例句

eccentric moment偏心力矩
1.The production and change trend of copper water eccentric moment in converter process is discussed.讨论了在转炉生产过程中炉内铜水偏心力矩的产生及其变化趋势 ,并提出了炉体在不同转角时炉内铜水偏心力矩的计算方
3)eccentric torsion偏心扭矩
4)eccentric bending moment偏心弯矩
1.For gabled frames structure with crane,both upper load and heel eccentric bending moment of which are relatively large,when ground is very weak,adopting the pile foundation to resist to pull out and to press is one kind of comparatively suitable method for ground treatment.对于装备吊车的门式刚架结构,上部荷载和柱脚处偏心弯矩较大,当地基很软弱时,采用桩基进行抗拔和抗压是一种较为合适的地基处理办法。
5)eccentric torgue ratio偏心矩比
1.Getting the system response through numerical integration,the effects of the mass ratio of stator to rotor and eccentric torgue ratio of the two disks on the system bifurcation and chaos were analyzed.提出了考虑机匣弹性、机匣与定子间的弹性联接和陀螺效应的碰摩转子动力学系统模型;运用数值积分方法获取了系统响应,分析了机匣与圆盘质量比和双圆盘偏心矩比对转子系统分岔与混沌行为的影响。
6)centro-bias moment vector偏心矩向量
延伸阅读

在AutoCAD中偏心圆锥与偏心圆台实体的画法现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上. 1)连接PA,PB. A(-100,0,0) B(100,0,0)图1在当前坐标下: 2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;3)连接CD;4)以CD为直径画圆;5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;6)过O作CD的垂线,交圆于E,F;图27)用三点UCS命令,取三点为:O,P,C; 8)过点O作PO的垂线GO,交PC于G;图39)再次用三点UCS命令,取三点为O,F,G; 10)现在就可以画椭圆锥了!cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;图411)回到WCS,剖切椭圆锥 SL-选择椭圆锥-回车-XY-回车-捕捉P点.12)删除辅助线条.图5