1)multi-tables多工作台
2)multi-degrees-of-freedom worktable多轴工作台
1.Design of system and control flow chart are introduced detailedly in this article,the correlative experimentions have been done on multi-degrees-of-freedom worktable,and the results show the control requirement of system application is achieved basically.文章详细介绍了系统的设计,给出了控制流程图,并在开发的多轴工作台上进行了相关实验,基本上达到了系统应用的控制要求。
英文短句/例句
1.Research on Distributed Motion Control System Based on DSP and CAN Bus for Multi-Degrees-of-Freedom Worktable;基于DSP和CAN总线的多轴工作台分布式运动控制系统研究
2.Research on the Multi-Axis Transformation of the Three-Axis CNC Machine Tool Based on the Rotary Worktable;基于回转工作台的三轴数控机床多轴化改造研究
3.distance from spindle nose to central line of table主轴端面至工作台中心线距离
4.Structure and Working Principle of NC Two-axis Rotary Table数控双转轴式回转工作台的结构与工作原理
5.Programming for 5-axis Machine with Swivel Tool Axis Integrated Rotary table工作台回转与刀轴摆动五轴联动数控加工编程技术研究
6.The Stress Analysis of Hub Bearing Based on Multi-bench Test Load基于多工况台架试验载荷的轮毂轴承受力分析
7.Parameter calibration research of the turntable for 4-axis 3D laser measuring system4轴3D激光测量系统中旋转工作台参数标定
8.parallel swivel bench vice平行轮轴钳工台虎钳
9.Fracture accidents occurred on the second shaft of automobile gearbox during operation.汽车变速箱二轴在工作中发生多起断裂事故。
10.Bandwidth Influence of Three-Axis Motion Table on Dynamic Performance of Torpedo Control System三轴转台工作频带对鱼雷控制系统动态性能的影响
11.index table machine多面回转工作台式组合机床
12.Euripides: Fine. So what do we need, about a thousand workstations?好。那我们差不多要一千台工作站吧?
13.The Electro-Magnetic Compatibility of Several Sets of the Transceivers Equipped in the Same Vehicle in the Co-site Mode;多部电台同车同址工作时的电磁兼容
14.At the latter laboured quite a company of girls and some men.工作台旁许多姑娘和一些男工正在干活。
15.multi-engine geared drive power plant多台发动机共轴齿轮传动动力装置
16.multi-engine geared drive多台发动机共轴齿轮传动
17.Axle Input Operating Angle −7°车轴输入工作角 −7°
18.single-axial mode operation激光器单轴模式工作
相关短句/例句
multi-degrees-of-freedom worktable多轴工作台
1.Design of system and control flow chart are introduced detailedly in this article,the correlative experimentions have been done on multi-degrees-of-freedom worktable,and the results show the control requirement of system application is achieved basically.文章详细介绍了系统的设计,给出了控制流程图,并在开发的多轴工作台上进行了相关实验,基本上达到了系统应用的控制要求。
3)platform[英]['pl?tf?:m][美]['pl?t'f?rm]工作台，平台
4)working surface of table工作台台面
5)Table[英]['te?bl][美]['tebl?]工作台
1.Design of Table Index Function of Machining Center by Indexing Axis;用分度数控轴实现加工中心工作台分度功能的设计方法
2.Design of Table Feeding Device of Large Gantry Machining Center;大型龙门加工中心工作台进给系统设计
3.Error analysis on the X-Y table in automatic gold wire bonder;全自动金丝球焊机X-Y工作台的误差分析
6)Workbench[英]['w?:kbent?][美]['w?k'b?nt?]工作台
1.The Common Faults and Removal Method of the Y3150 E Type Hobbing Machine Workbench;Y3150E型滚齿机工作台的常见故障及排除方法
2.Some of Operation Breakdowns and Solving Ways on Machine Tool Workbench;机床工作台的几种运行故障及其解决办法
3.Study on the hot deformation for workbenchsupported by hydrostatic guideway of vertical lathe立式车床静压导轨支承工作台的热变形研究与改进
延伸阅读
卧式单轴、多轴自动半自动操作规程适用机型：1、 单轴自动车床：CG110（1A10?），C1318（1A118），C1325（1A124），C1336（1A136），A12，A20，A40。2、 多轴自动、半自动车床：C24·4（1240·4），C25·4，C2140·P4，C2150·4D，C2132·6D，C2132·6，C24·6（1240·6），C2150·6D，C2216·6，BSA1/2 -4，1290，ANK135，ANK155，1261M，1261?，1265·6，1265M·6，1240-0一、认真执行《金属切削机床通用操作规程》有关规定。二、认真执行下述有关补充规定：（一） 工作前认真做到：1、 检查分配轴及凸轮上的凸轮、撞块应完好无裂纹，安装正确，紧固牢靠。2、 调正机床时，棒料、毛坯的夹紧，只准用手动不准用机动。（二） 工作中认真做到：1、 不准加工弯曲、未经冷拨和未经倒角的棒料。2、 装料时须将料头对准夹头孔，轻轻击进。棒料长度一般以不超出料管200毫米左右为宜。3、 四轴自动车床不准在第四工位上装料。六轴自动、半自动车床不准在第六工位上装料。4、 保险键剪断时，就应查明原因，方准更换新键。
