1)eccentric compression偏心受压
1.Study on eccentric compression of rapidwall with concrete filled every one or more holes;纤维增强石膏板隔孔灌注混凝土偏心受压性能研究
2.Experimental study on deformation performance of median long columns with Yellow River silt cellular bricking structures subjected to eccentric compression;黄河淤泥多孔砖砌体中长柱偏心受压变形性能试验研究
3.Study of stress-strain relation of concrete filled steel tubular eccentric compression column;钢管混凝土偏心受压应力-应变关系模型研究
英文短句/例句
1.Experimental study on eccentric compression behaviour of autoclaved flyash-lime brick masonry蒸压粉煤灰砖砌体偏心受压性能试验
2.Calculating the eccentric compressive bearing capacity of the rapid wall by the method of appendant eccentricity附加偏心距法求解速成墙板偏心受压承载力
3.The Stability Calculation of Slight Sections Column Pressed by Single-direction Eccentric Force;窄截面柱单向偏心受压时的稳定计算
4.Reliability analysis of RC members subjected to eccentric compression based on random characteristics of eccentricity基于偏心距随机特性的混凝土偏心受压构件可靠度分析
5.A Precise Algorithm for the Relative Depth of Compressive Zone about The Compression Member with Small Eccentricity in Bridge Engineering桥梁工程中小偏心受压构件相对受压区高度的精确计算方法
6.Experimental Research on the Behavior of Reinforce Concrete Special-shaped Column with Different Length of Limbs under Axial Compression and Biaxial Bending;钢筋混凝土不等肢异形柱偏心受压试验研究
7.Experimental Study on Buckling Capacity of Slender Steel Reinforced Concrete Columns Subjected to Eccentric Load;偏心受压钢骨混凝土长柱稳定承载力试验研究
8.Experimental Research on the Carrying Capacity of Corroded R.C. Columns;锈蚀钢筋混凝土偏心受压柱承载力试验研究
9.The Experimental Study on the Capacity for Reinforced Concrete Masonry Columns Subjected to Eccentric Load;配筋砌块砌体柱偏心受压承载力的试验研究
10.Experiment Study on Reinforced Masonry Walls under out of Plane Eccentric Load;配筋砌体墙片出平面偏心受压试验研究
11.The Reinforcement of the Special-shaped Columns under Bi-directional Eccentric Load by Computer;双向偏心受压异形柱计算机辅助配筋计算
12.Research on Behavior of Inequiaxial Specially Shaped Column Subjected to Biaxial Compression;不等肢异形截面双向偏心受压柱性能研究
13.Theoretical Research on the Load Capacity of Eccentric Compressive Circular Section Column by Enclosed Reinforcement;围套加固偏心受压圆截面柱承载力理论研究
14.Research on Bearing Capacity of Normal Section for Steel Reinforced Concrete Columns under Biaxial Eccentric Compression型钢混凝土柱双向偏心受压正截面承载力研究
15.The Studies on Fire Resistance Performance of Eccentrical Compressive Concrete-Filled Thin-Walled Steel Tube Columns偏心受压薄壁钢管混凝土柱抗火性能研究
16.The Research on Eccentric Pressure of Cross-Shaped Section Column with Steel Reinforced Concrete Columns十字形钢骨混凝土异形柱偏心受压研究
17.Experimental behavior of BFRP-confined circular short RC columns under eccentric loadingBFRP约束钢筋混凝土短柱偏心受压试验研究
18.Ring Type Stirrups Welded High-strength Concrete Columns Experimental Study of Large Eccentric焊接环式箍筋高强砼大偏心受压柱试验研究
相关短句/例句
Eccentric pressure偏心受压
1.Using the real stress\|strain relation of concrete material,a method to determine the ultimate load of concrete circular\|section column under eccentric pressure is discussed,and an ultimate load versus eccentricity curve is obtained.采用规范规定的混凝土应力 -应变关系 ,对圆形截面混凝土偏心受压构件的极限承载力作了理论分析和计算 ,得到极限承载力 -荷载偏心距曲
3)little eccentric compression小偏心受压
1.Direct calculation of symmetric reinforcement for rectangular cross sectional little eccentric compression member;矩形截面小偏心受压构件对称配筋的直接计算
4)eccentrically compressed column偏心受压柱
1.Taking the parameters of load eccentricity e_0/h,slenderness ratio l_0/h as variables,bond-slip tests were carried out on 20 SRC eccentrically compressed columns.以荷载偏心距 e_0/h、构件长细比 l_0/h 为主要参数,进行了20根型钢混凝土偏心受压柱的粘结滑移性能试验,观察了试件的破坏形态,分析了型钢混凝土内部粘结应力和滑移的分布规律。
5)large eccentric compression大偏心受压
1.Calculation of bearing capacity for steel reinforced concrete=column subjected to large eccentric compression load;钢骨混凝土大偏心受压柱承载力计算
6)eccentrically compressed pile偏心受压桩
1.The computing method for piles recommended in the specifications for architectural design of ground base(GB 5007-2002) is comparatively applicable to the calculation of axially compressed piles,but rather complicated to that of eccentrically compressed piles.建筑地基基础设计规范(GB50007 2002)给出的桩身计算方法对轴心受压桩较为适用,但对于偏心受压桩的计算则非常繁琐。
延伸阅读
在AutoCAD中偏心圆锥与偏心圆台实体的画法现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上. 1)连接PA,PB. A(-100,0,0) B(100,0,0)图1在当前坐标下: 2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;3)连接CD;4)以CD为直径画圆;5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;6)过O作CD的垂线,交圆于E,F;图27)用三点UCS命令,取三点为:O,P,C; 8)过点O作PO的垂线GO,交PC于G;图39)再次用三点UCS命令,取三点为O,F,G; 10)现在就可以画椭圆锥了!cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;图411)回到WCS,剖切椭圆锥 SL-选择椭圆锥-回车-XY-回车-捕捉P点.12)删除辅助线条.图5