1)as-cast铸态
1.Microstructure and properties of the as-cast and annealing Mg-Li-Al-Zn-RE alloys;Mg-Li-Al-Zn-RE合金铸态和退火态的组织与性能
2.Effect of annealing treatment on microstructure and properties of as-cast austenitic-bainite nodular iron by permanent mold casting;退火处理对金属型铸态奥—贝球铁组织和性能的影响
3.Study on as-cast casting process of Cummins 6BT exhaust manifold;康明斯6BT排气歧管铸态生产工艺的研究
英文短句/例句
1.Microstructure and Properties of Cr-Alloyed As-Cast Nodular Iron--Application of Cr in As-Cast Nodular Iron(Ⅰ)Cr合金铸态球墨铸铁的组织和性能——Cr在铸态球墨铸铁中的应用(1)
2.The Fatigue Property of As cast HCC Ductile Iron Bars水平连铸铸态铁素体球墨铸铁型材的疲劳性能
3.Study on Abrasion Resistance of the Columnar Grain Zone in High Cr Cast Iron铸态高铬铸铁柱状晶粒区耐磨性研究
4.Study on the Manufacturing Procedure of Cast Ferritic Ductile Iron;铸态铁素体球墨铸铁的生产工艺研究
5.Study on Preparation and Microstructure of As-cast QT550-7 Ductile Iron铸态QT550-7球墨铸铁制备及组织研究
6.Control on Smelting Process of As-Cast QT450-10 Nodular Graphite Iron铸态QT450-10球墨铸铁熔炼过程控制
7.Microstructures and Mechanical Properties of As-Cast and Die-Cast Mg-Al-Nd Magnesium Alloys铸态和压铸态Mg-Al-Nd镁合金组织与力学性能
8.The abrasive resistance of as-cast martensitic high chromium cast iron is 3 times more than that of Ni-hard cast iron.铸态马氏体高铬铸铁的耐磨性是镍硬铸铁的3倍以上。
9.Influence of Molybdenum、Boron and Copper on Mechanical Properties of As-Cast High Chromium Cast Iron钼硼铜对铸态高铬铸铁力学性能的影响
10.A Study on As-Cast NoduIar Cast Iron Containing Sb、Al and Ti in Crankshaft Production含锑、铝、钛铸态球墨铸铁曲轴材料的研究
11.Observation and Analysis on the Microporosity in As-Cast Bainite Grey Cast Iron铸态贝氏体灰口铸铁中显微缩松的观察分析
12.Production of as cast automobile parts of s.g. cast iron with high strength and toughness高强度/高韧性铸态汽车球墨铸铁件生产技术
13.Study on Wear Resistance of As-cast High Cr-Mn Austenitic White Cast Iron铸态高铬锰奥氏体白口铸铁抗磨性试验研究
14.A Study of the Abrasion Chracteristics of As-Cast Austenitic High Chromium White Cast Iron铸态奥氏体高铬铸铁抗磨料磨损特性的研究
15.Cast Microstructure Design of low Chrome White Cast Iron Grinding Ball浅析低铬白口铸铁磨球的铸态组织设计
16.Development and Application of Die Cast Hammer Made of Composite Metal金属型复合铸造铸态锤头的研制及应用
17.Research on Homogenization and Mass Transfer in AZ61 Magnesium Alloy Ingot;铸态AZ61镁合金铸锭均匀化处理及扩散传质研究
18.The Experiment Research on As-Cast High Toughness Ductile Iron Cooling Wall for Blast Furnace;铸态高韧性球墨铸铁高炉冷却壁的试验研究
相关短句/例句
as cast铸态
1.Results show that creep of as cast alloy and alloy stabilized by heat treatment increased with temperature and compressive stress,and the steady creep rate of as cast alloy is greater than that of alloy stabilized heat treatment.研究表明 ,在试验温度为2 0℃到 16 0℃和压应力为 5 0MPa到 137 5MPa的范围内 ,合金在稳定化处理及铸态下的压蠕变量均随着温度和应力的升高而增大 ,稳定化处理状态下的压蠕变速率大于铸态下的蠕变速率。
2.This paper studies the influence of adding amount of trace elements and opening time on the amount of pearlite and properties of as cast nodular cast iron according to practical production requirement.针对生产实际要求 ,研究了微量元素加入量、开箱时间等对铸态球墨铸铁珠光体量及性能的影响 ,试验了铸态球墨铸铁曲轴的各种常规性能。
3.The chemical composition,microstructure,mechanical properties,production system and economic benefit of as cast ferrite/perlite spheroidal graphite cast iron miner’s truck wheel are introduced.介绍了铸态铁素体－珠光体球墨铸铁矿车轮的化学成分、组织性能、生产工艺及经济效益。
3)cast[英][kɑ:st][美][k?st]铸态
1.Study on the Manufacturing Procedure of Cast Ferritic Ductile Iron;铸态铁素体球墨铸铁的生产工艺研究
2.The degree of uniformity of bulk standard material using for spectroscopic analysis,depended on the preparation of material in a large extent,some of the cast standard material production system easily lead alloy structure to a gradient distribution along sample depth direction,but uncertainty components of for it often can not be overlooked,should be considered joining the total uncertainty.光谱分析用块状标准物质的均匀化程度,在很大程度上取决于标准物质的制备方式,某些铸态标准物质的制作系统容易产生合金组织沿样品深度方向形成梯度分布,由其产生的不确定度分量,往往不容忽略,应考虑加入总不确定度中。
4)as-cast microstructure铸态组织
1.Morphology and Phase Constituent of Secondary Phase in As-cast Microstructure of 7150 Aluminum Alloy;7150铝合金铸态组织中第二相的形貌及相组成
2.Effects of Trace Si,Ba and Sn on the As-cast Microstructure of AZ91 Magnesium Alloy;微量Si、Ba、Sn对AZ91铸态组织的影响
3.Effect of lithium on as-cast microstructure of Mg-2Al-1Zn-4Y-3Nd alloy;Li含量对Mg-2Al-1Zn-4Y-3Nd合金铸态组织的影响
5)Casting bar铸态线坯
6)As-cast structure铸态组织
1.On the basis of twin-roll thin strip continuous casting experiments, structure and composition analysis, the as-cast structure characteristics of 1Cr18Ni9Ti stainless steel twin-roll thin strip were investigated.通过双辊薄带连铸试验和组织成分分析,对1Cr18Ni9Ti不锈钢双辊薄带的铸态组织特征进行了研究。
2.The effect of yttrium on as-cast structure and age hardening of the magnesium alloy Mg-9Al-1Zn were investigated.研究了稀土元素钇 (Y)对Mg 9Al 1Zn合金铸态组织及时效硬化特性的影响。
3.The investigation was carried out experimentally on as-cast structure evolution of horizontal continuous casting aluminum alloy under combination electromagnetic field.采用试验的方法研究了组合磁场作用下5182铝合金水平连铸过程中铸态组织的演变。
延伸阅读
铸态高铬屈氏体磨球的生产摘要：本文从优化成分设计、熔炼、变质处理、铸造及热处理等工艺控制措施入手，综合介绍了铸态高铬屈氏体磨球的生产过程，并经生产试验使各工艺参数达最佳匹配，为生产出高质量的铸态高铬屈氏体磨球提供了强有力的理论支撑。关键词：高铬屈氏体磨球优化工艺控制含铬大于11%的铬系白口铸铁成为高铬铸铁，马氏体Cr15高铬铸铁是目前国内外广泛应用的较典性的耐磨铸铁，用于制造磨球、衬板等，取得了较好的节材降耗效果。马氏体高铬铸铁磨球具有较高的硬度，但韧性较差。马氏体Cr15磨球是经热处理淬火加回火的工艺获得的，因此需要一套专用的热处理设备。这不仅投资及能源消耗大、生产周期长、生产成本也较高，从而影响了它的广泛应用。我们的目的是研制一种既有高铬铸铁的耐磨性和韧性，生产工艺简单、成本低廉的材料：铸态高铬屈氏体磨球。它与淬火马氏体Cr15磨球相比，具有省工、省时、省能耗、省原材料消耗的的优势。它的生产应用能产生较大的社会效益。一．成分设计碳：碳为生成共晶碳化物（Cr·Fe）7C3的主要元素，共晶碳化物在耐磨性方面起着重要作用。碳含量决定碳化物的数量。选择较高的碳含量，可获得较多的高硬度碳化物。为提高耐磨性，碳的质量分数应控制在2.8～3.1%。铬：铬含量决定碳化物的类型。为保证碳化物以M7C3为主，铬含量必须大于12%，过低不能形成高硬度的（Cr·Fe）7C3型碳化物；过高则成本提高。因此铬的质量分数为12～14%。
