1)sulfonitriding硫氮共渗
1.A new method of sulfonitriding processing by induction heating has been developed This technique can save energy and elimate environmental pollution and mak the workpiece obtaining good properties,such as wear resistance,corrosion resistance,thermal fatigue resistanc利用高频热源开发硫氮共渗新技术，可节约能源，减少环境污染，并使零件获得耐磨、耐蚀、耐热疲劳等综合性能。
2.The high freguency sulfonitriding layers has been characterized by using X-ray diffraction method in this paper.本文利用X射线衍射仪对高频硫氮共渗层的相结构进行了分析,发现渗层表层部位主要由FeS、Fe_3O_4及ζ-Fe_2N等相组成,中间白亮层为ζFe_2N+ε-Fe_3N,扩散层由α-Fe+ε-Fe_(2-3)N等组成。
3.This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.研究了高速钢经硫氮共渗处理后的耐磨性及抗咬合性，并与未经表面处理的试样进行了比较。
英文短句/例句
1.Tribological Properties of Sulfur-nitrade Layer on Drilling Joint Material 35CrMo Steel钻杆接头材料35CrMo钢硫氮共渗层的摩擦学性能
2.An Investigation of the Conventional HSS Cutting Performance by SOCNB Complex Permeation Treatment Method硫氧碳氮硼复合共渗高速钢刀具切削性能的研究
3.Research of the Cylinder Sleeve and Piston Ring of Marine Diesel be Third Element Together Permeate Deal with Sulfur-charcoal Glow Ionic Nitriding;船用柴油机气缸套及活塞环采用辉光离子硫碳氮三元共渗的研究
4.liquid carbonitriding液体碳氮共渗, 液体渗碳氮化法
5.Gas Nitrocarburzing for 4Cr5MoSiV1 Steel4Cr5MoSiV1(H13)钢的气体氮碳共渗
6.Surface Compound Treatment of C-N Multi-elements and RE-B-C-N Multi-elements Deep-penetrating碳氮共渗-深层稀土硼碳氮共渗复合处理
7.Study on the hydrogen embrittlement phenomena of carbonitriding tape gear;合金渗碳钢锥齿轮碳氮共渗的氢脆现象研究
8.Influence of nitrocarburizing on microstructure and roughness of 4Cr10Si2Mo steel氮碳共渗对4Cr10Si2Mo钢渗层组织和表面粗糙度的影响
9.Research on Ion-nitrocarburizing Processes and Mechanism with N_2 and CH_4 for 40Cr;40Cr钢氮气—甲烷离子氮碳共渗工艺及机理的研究
10.new technology of ionitro-carbon-titanizing离子氮-碳-钛三元共渗新工艺
11.Investigation of Plasma Electrolytic Carbonitriding Technique in Solution;液相等离子体电解碳氮共渗技术研究
12.RE-nitrocarburizing Technology for Piston Rod Made of 40CrMnMo40CrMnMo活塞连杆稀土离子氮碳共渗工艺
13.RE-B-C-N multi-element penetration of 65Mn steel metal rubber with larger wire diameter大丝径65Mn金属橡胶稀土硼碳氮共渗
14.Effect of Ion Nitriding-Sulfurizing Composite Treatment on Tribological Behavior of Ti-6Al-4V离子渗氮—渗硫复合处理对Ti-6Al-4V合金摩擦学性能的影响
15.Effect of Nitriding-sulfurizing Composite Treatment on Tribological Behavior of Titanium Alloy渗氮-渗硫复合处理对Ti-6Al-4V合金摩擦学性能的影响
16.The heat treatment technology of carbo- nitriding of steel has the characteristic of lower treatment temperature and direct quenching.钢的碳氮共渗热处理工艺具有共渗温度低、直接淬火等特点。
17.Surface combined treatment of carbonitriding and B-C-N-RE multi-elements deep-penetrating on 20Cr steel firebrick die碳氮共渗-深层稀土硼碳氮共渗复合处理在20Cr钢耐火砖模具中的应用
18.Measurement on the carbonizing or nitro-caburizing harden case depth of sintering iron-based materialGB/T9095-1988烧结铁基材料渗碳或碳氮共渗硬化层深度的测定
相关短句/例句
sulpho carbonitriding硫碳氮共渗
3)sulphonitrocarburizing硫氮碳共渗
4)liquid sulpho-nitrocarburizing液体碳氮硫共渗
1.The microstructure morphology of 38CrMoAl steel axial plunger after gas nitrocarburizing and liquid sulpho-nitrocarburizing were analyzed and observed by optical microscope and SEM,and the chemical composition of the penetrated layer were measured qualitatively by energy spectrum analysis.用金相显微镜和扫描电镜观察和分析了38CrMoAl钢轴向柱塞经气体氮碳共渗和液体碳氮硫共渗后的组织形貌,并且用能谱分析的方法定性地测定了渗层的化学成分。
5)ion S-N-C co-diffusion离硫氮碳共渗
6)sulpho-nitrocarburizing in salt bath液体硫氮碳共渗
延伸阅读
碳氮硫三元共渗分子式：CAS号：性质：又称硫氰共渗。可同时改善钢及铸铁工件的耐磨性及减磨性。共渗层深度为10μm，其组织与渗剂的组成有关。以渗硫为主时，表层有FeS或FeS加α-Fe；以渗氮为主时，有Fe2(N，C)及Fe4(N，C)；以渗碳为主时，则形成Fe3(C，N)。其工艺主要有粉末法、膏剂法和盐浴法三种。
