1)half-axle后桥半轴
1.The microstructure and fracture features of 40Cr rear half-axle used in a car were analyzed by optical metalloscope and SEM.采用光学显微镜和扫描电子显微镜等手段 ,对某轻型汽车 4 0Cr后桥半轴断裂件的组织及断口特征进行了分析结果表明 :半轴在调质处理时的淬火温度不够高 ,使其表层和心部组织中存在较多的铁素体相 ,造成了工件最终的硬度和疲劳强度不足 ,导致半轴在使用中发生扭转疲劳断裂 。
英文短句/例句
1.Improvement in forging die design for half shaft tube of rear axle of 1061 model car1061型汽车后桥半轴管锻模设计的改进
2.Analysis of new rotary-forging process of rear-semiaxis using Deform-3D基于Deform-3D的后桥半轴摆辗新工艺分析
3.half-shaft (excl. internal parts of engines) for motor vehicles后桥半轴（不包括发动机的内部零件）,机动车辆用
4.Application of Three-Roller Cross-Rolling in Half-Shaft Casing for middle-sized vehicle;特轧工艺在中型车后桥半轴套管中的应用
5.Research on Development and Application of High Performance Non-hardened Tempered Steel for Semi-axle of Automotive Rear Axle汽车后桥半轴用高性能非调质钢的开发及应用研究
6.rear axle differential side gear后桥差速器半轴齿轮
7.The rear axles are attached to the wheels and have bevel side gears on their inner ends.后桥与车轮相连,内端装有一个半轴齿轮。
8.Radius arms, cross members, radius arm brackets and cross member brackets rebuilt or modified for new axle locations.根据新的前后桥的位置，对半轴，十字轴及相关支架进行改造。
9.semimajor axis of ellipsoid椭球长半轴，地球长半轴
10."The differential is part of the rear-axle-housing assembly, which includes the differential, rear axles, wheels, andbearings."差速器是后桥壳总成的一个部件,后桥壳总成包括差速器、后桥、车轮和轴承。
11.Automobile Vehicle Bridge Welding Equipment of Axle Tube and Transitional Flange for PLC Control and Welding Procedure;汽车车桥半轴套管、过渡接盘焊接设备PLC控制及焊接工艺
12.Research on the Turning Traits of Three-axles Semi-trailer and the Structure Principles of Self-steering Axle三轴半挂车转向协调性及随动转向桥结构原理研究
13.Failure Analysis for Semi-shaft Fracture in Front Axle of a New Type Loader and Its Improving Measures某新型装载机前桥半轴断裂失效分析及改进措施
14."Semifinished main bearings require finishing and fitting after installation, so that the crankshaft must be taken out."半精加工的主轴承安装后需要修整和调配,这样曲轴就必须拆下。
15.Techniques Research on Extrusion and Precision Forging for Transit's Back-bridge Semi-Axle Shaft Sleeve;全顺汽车后轿半轴套管挤压精锻工艺研究
16.The reason the propeller shaft shortens as the angle increases is that the rear axle and differential move in a shorter arc than the propeller shaft.当角度增加时,传动轴变短的原因是后桥和差速器运动的弧度小于传动轴运动的弧度。
17.Either half of the major axis is called a semimajor axis.长轴的每一半叫做半长轴。
18.The chemically extracted acellular muscle graft promotes axonal growth after spinal cord hemisection化学去细胞肌肉促进大鼠脊髓半横断后的轴突再生
相关短句/例句
auto semiaxles汽车后桥半轴
3)shaft assy.,rear axle后桥半轴总成
4)rear axle differential side gear后桥差速器半轴齿轮
5)Semi-shaft in front axle前桥半轴
6)semi-shell of the rear bridge后桥半壳
延伸阅读
卧式单轴、多轴自动半自动操作规程适用机型：1、 单轴自动车床：CG110（1A10?），C1318（1A118），C1325（1A124），C1336（1A136），A12，A20，A40。2、 多轴自动、半自动车床：C24·4（1240·4），C25·4，C2140·P4，C2150·4D，C2132·6D，C2132·6，C24·6（1240·6），C2150·6D，C2216·6，BSA1/2 -4，1290，ANK135，ANK155，1261M，1261?，1265·6，1265M·6，1240-0一、认真执行《金属切削机床通用操作规程》有关规定。二、认真执行下述有关补充规定：（一） 工作前认真做到：1、 检查分配轴及凸轮上的凸轮、撞块应完好无裂纹，安装正确，紧固牢靠。2、 调正机床时，棒料、毛坯的夹紧，只准用手动不准用机动。（二） 工作中认真做到：1、 不准加工弯曲、未经冷拨和未经倒角的棒料。2、 装料时须将料头对准夹头孔，轻轻击进。棒料长度一般以不超出料管200毫米左右为宜。3、 四轴自动车床不准在第四工位上装料。六轴自动、半自动车床不准在第六工位上装料。4、 保险键剪断时，就应查明原因，方准更换新键。
