淬火-碳分配-回火(Q-P-T)工艺,quenching-partitioning-tempering(Q-P-T)process英语短句,例句大全

淬火-碳分配-回火(Q-P-T)工艺,quenching-partitioning-tempering(Q-P-T)process
1)quenching-partitioning-tempering(Q-P-T)process淬火-碳分配-回火(Q-P-T)工艺
1.In 2007,the present author proposed a novel heat treatment process,quenching-partitioning-tempering(Q-P-T)process,based upon the Q-P process,i.在Q-P工艺基础上,本文作者于2007年建议一个热处理的新工艺:淬火-碳分配-回火(Q-P-T)工艺,即淬火至Ms～Mf后,除作碳分配外,还在一定温度回火一定时间,使析出复杂碳化物,以增加强化作用。

英文短句/例句

1.A brief introduction to quenching-partitioning-tempering (Q-P-T) process淬火-碳分配-回火(Q-P-T)工艺浅介
2.Study on three-body impact-abrasion of steel treated by quenching-partitioning-tempering process淬火-配分-回火工艺处理钢的三体冲击磨损性能研究
3.Water Quenching and Tempering Technology Research of 1000MPa Ultra-High Strength Dual-Phase Steel;1000MPa超高强双相钢水淬及回火工艺研究
4.Influence of Quenching Temperature on Microstructure and Mechanical Properties of Q&P Super-high Strength Steel超高强Q&P钢淬火温度对组织和性能的影响
5.Direct Quenching Technical Study of Ti-B Microalloying Low Carbon Si-Mn SteelTi-B微合金化低碳Si-Mn钢直接淬火工艺研究
6.Optimization of Cam's Carburizing and Quenching Technology of High-powered Marine Diesel Engine大功率船用柴油机凸轮渗碳淬火的工艺优化
7.Step Iso-Thermal Quenching Process Used to Obtain Heavy Section ADI Casting用于厚大ADI铸件的分级淬火工艺
8.The Quenching Procedure Test of SA387Gr11CL2SA387Gr11CL2钢淬火工艺试验
9.Research on Sub-temperature Quenching Process of 30CrMnSiA Steel30CrMnSiA钢亚温淬火工艺研究
10.Research on Heat Treatment Technology of 5CrMnMo Hot Forging Die5CrMnMo热锻模淬火工艺研究
11.Impact of 60Si2MnA wire rod decarburization on oil-hardened and tempered steel wire60Si2MnA线材脱碳对油淬火—回火钢丝脱碳的影响
12.Subcritical Quenching Technique for 45 Steel May Reduce Quenching Dehiscence Tendency45钢亚温淬火工艺可减少淬火开裂倾向
13.Tempering softening of overlapping zones during multi-track laser quenching for carbon steel and alloy steel碳钢及合金钢搭接激光淬火回火软化特征
14.Study on Immediate Quenching Process of Martensitic Based Spheroidal Graphite Cast Iron Grinding Ball马氏体基球墨铸铁磨球的余热淬火工艺分析
15.The heat treatment technology of carbo- nitriding of steel has the characteristic of lower treatment temperature and direct quenching.钢的碳氮共渗热处理工艺具有共渗温度低、直接淬火等特点。
16.Study on the Effect of Material and Technology Factors on the Distortion of Carburizing and Hardening Gears;材料和工艺因素对渗碳淬火齿轮畸变影响的研究
17.continuous quench and temper line淬火回火连续作业线
18.The case-hardening or carburizing process is in wide use.表面淬火或渗碳法应用十分广泛。

相关短句/例句

Q-P-T processQ-P-T(淬火-分配-回火)
1.As a result,the impact abrasive wear resistance of steel 20Si2Ni3 treated by Q-P-T process and Q-T process are superior to that of high manganese steel.对自行研制的新型马氏体耐磨钢20Si2Ni3进行了Q-P-T(淬火-分配-回火)及传统淬火-回火(Q-T)热处理,用MLD-10型动载磨料磨损实验机比较在1。
3)quenching-partitioning-tempering process淬火-配分-回火工艺
1.Study on three-body impact-abrasion of steel treated by quenching-partitioning-tempering process淬火-配分-回火工艺处理钢的三体冲击磨损性能研究
4)Process of quenching and tempering淬回火工艺
5)quenching process淬火工艺
1.Effects of quenching process on structures and properties of Fe-V-W-Mo alloy;淬火工艺对Fe-V-W-Mo合金组织和性能的影响
2.With the finite element code of MSC Marc, the quenching under the complicated quenching process of the large-sized block made of P20 was simulateds.采用有限元软件MSCMarc模拟大型P20钢模块在复杂淬火工艺下的冷却过程,通过分析淬火过程中的温度变化历程及最终组织分布,为厂方生产的P20钢模块制定合理的淬火工艺。
3.Two new quenching processes were Numerically simulated for the plastic die steel 718.借助计算机数值模拟,为塑料模具钢718大模块制订了两种新型的淬火工艺,一是预冷-水淬-自回火-水淬工艺,另一是提高奥氏体化温度,直接空冷淬火的工艺。
6)quench process淬火工艺
1.Through making scientific test to the quenching deformation of the key slot on the shaft with the material20CrMnTi,the best quench process is given to control the quenching deformation.通过对20CrMnTi材料轴上键槽淬火变形进行试验,得到最佳淬火工艺,并对键槽淬火变形加以控制。