1)Workpiece[英]['w?:k,pi:s][美]['w?k,pis]轧件
1.The Mathematic Model of Workpiece Deformation Region of Cross Wedge Rolling楔横轧轧件变形区几何形状的数学模型
英文短句/例句
1.Analysis of Factors Affecting Instantaneous Speed Ratio between Workpiece and Roller of CWR楔横轧轴类零件轧件与轧辊瞬时速比影响因素分析
2.Abstract: Determining nip point is important for steady rolling section steel.文摘:确定型钢轧制时轧件的咬入点对实现稳定轧制有重要意义。
3.Study on Head Warping and Control for Plate Rolling中厚板轧制轧件头部弯曲及其控制的研究
4.Research on material flow trait during cross wedge rolling process楔横轧变形过程中轧件内部金属流动的规律
5.Study on the quality effect of rolled piece internal part in two rolls cross wedge rolling by J.T.S methodJ.T.S法对改善二辊楔横轧轧件心部质量的研究
6.Study on prediction of strip profile and strip edge drop of a Sendzimir mill森吉米尔轧机轧件板形与边部减薄预报研究
7.Effect of Workpiece Torsion on Rolling Stableness during High-speed Wire Rod Rolling轧件扭转对高速线材轧制稳定性的影响
8.Analytical Model for Cross-Sectional Area of Workpiece in Round-Oval-Round Pass Sequence in Bar Rolling棒材轧制圆-椭圆-圆孔型中轧件面积计算模型
9.The Mathematic Model of Workpiece Deformation Region of Cross Wedge Rolling楔横轧轧件变形区几何形状的数学模型
10.total elongation and fish-tail change with liquid core rate of steel ingot; join mark and splits etc. produced surface of the rolled metal.轧件的总延伸和鱼尾量随轧件的液芯率而变化,在轧件表面产生交接痕及裂纹等。
11.Software Development for Predicting Strip Profile and Strip Edge Drop of a 20-high Mill20辊轧机轧件截面形状与边部减薄预报软件开发
12.Plastic deformation heat and friction heat are the two principle factors which caused the temperature rise of cold rolled thin plate.冷轧时轧件塑性变形热和摩擦热是导致轧件温度升高的两个主要原因。
13.bar throw-off gear(从辊道拨往冷床)轧件拨出装置
14.roll-chock washing machine轧辊轴承部件清洗装置
15.The Research on Ring Rolling CAD/CAPP System;环件轧制CAD/CAPP系统研究
16.The Research and Development of Production Lot Planning System of Hot Rolling Strips;热轧带钢轧制批量计划软件系统开发与研究
17.Founding of Heavy Steel Castings-The Blooming Mill Housing Used for Ma Steel 2250mm hot mill马钢热轧2250mm初轧机架大型铸钢件的铸造
18.Software of forecasting finish rolling temperature for HSM was developed based on the traditional strip temperature dropping model.在传统热连轧精轧机组温降模型基础上，开发了带钢热连轧终轧温度预报软件。
相关短句/例句
workpiece[英]['w?:k,pi:s][美]['w?k,pis]工件;轧件
3)unit retrieval轧件检索
4)corner of workpiece轧件角部
1.Analysis of tendency of ductile fracture at corner of workpiece during grooveless rolling;无槽轧制轧件角部的韧性断裂趋势分析
5)pre-rolled blank预轧件
1.A typical conical ring with large height was given as an example,and on the basis of considering the technological conditions of rolling stability and axial flow of metal,the pre-rolled blank was designed throu.以典型的大高度锥形环锻件为实例,在考虑轧制稳定性、轴向金属体积流动等工艺条件的基础上,利用增大锥形环锻件大端壁厚的方法对锥形环锻件预轧件进行了设计。
6)shape of workpiece轧件形状
延伸阅读
轧件长度测量轧件长度测量length measurement of rolling stock zhalian ehangdu eeliang轧件长度测量(length measurement of roll-ing stock)轧件长度尺寸的在线检测。通常的长度测量方法是采用各种形式的信号变换传感器，经过信号处理求得被测体的长度值。由于参量长度、位移、速度相互之间有着密切的关系，因此，可利用位移传感器、速度传感器等达到测长的目的。也有利用红外线、放射线、电磁现象、光电技术的测长仪。 位移传感器测长位移传感器有差动变压器、同步感应器、磁栅、电动测微计、气动测微计、光电编码器、光电摄像传感器等。这些仪器都可以直接地或同必要的机构组合而成为长度测量仪。还可以使用角位移传感器如旋转编码器、电位计等经适当的机构转换作为直线尺寸测量仪。如用一定直径的辊子与被测物体接触，由物体的全长带动使之旋转，从它的旋转次数即可测出长度。 电磁波反射测长光波、激光、微波、超声波等自空间的一定点向某一物体发射，并从该物体表面反射回来，用仪器测出来回所需的传播时间，就能得到发射点到反射物体之间的距离。这是由于光波、激光、微波、超声波在某一已知的介质中有固定的传播速度，测得传播时间即可知波在介质中所走的距离即长度。但是，这些测量仪表在工业使用中却需要一定的条件，如超声仪表要求测头与被测体的接触处要有很好的藕合，一般使用某种藕合液。光学测量仪器要求光路中清洁无烟尘，反射物体表面要求无油污、物体反射率要尽可能大，以提高测量精度。 (申敬府朱德芳)
