1)multi-point forming多点成形
1.Sectional multi-point forming and its numerical simulation of plates;中厚板分段多点成形及其数值模拟
2.Numerical simulation on multi-point forming process for tailor-welded blank;拼焊板多点成形过程的数值模拟
3.Numerical simulation of springback on double-curved autobody panel during multi-point forming;双曲度覆盖件多点成形中回弹的数值模拟
英文短句/例句
1.Research on Rapid Shape Adjusting and Forming Process Automation in Multi-point Forming;多点成形中的快速调形与成形过程自动化研究
2.Rapid Calculation of Contact Points in Multipoint Forming CAD多点成形CAD中接触点的快速计算
3.Multi-point Forming Surface Generating Method and Software Development多点成形曲面的生成方法与软件开发
4.Numerical Simulation and Shaping Analysis on the Process of Multi-Point Forming for Thin Sheet Metal;薄板多点成形过程的数值模拟及成形性分析
5.Research on Continuous Multi-point Forming Method, Equipment and Experiment;连续多点成形方法、装置及成形实验研究
6.Spinning Technology Based on Principle of Continuous Multipoint Forming基于连续多点成形原理的旋压成形技术
7.Numerical Simulation and Forming Performance Comparison on the Process of Multi-Point Forming and Die Forming for Sheet Metal;薄板多点成形与模具成形过程数值模拟及成形性比较
8.Research on the Combined Forming Technology for Sheet Metal Based on Multi-point Forming & Incremental Forming Technology基于多点成形与渐进成形的板料复合成形技术研究
9.The Study of Finite Element Analysis on Multi-Point Forming Process of Sheet Metal;薄板多点成形过程有限元分析的研究
10.Numerical Simulation on the Process of Multi-point Forming for Tailor-Welded Blank;拼焊板多点成形过程的数值模拟研究
11.Study on the Numerical Simulation of Multi-point Forming Process for Retiary Sheet Metal带孔网板多点成形过程数值模拟研究
12.The Study on Multi-Point Forming Press and Its Key Components Used in Adjusting Elements;多点成形设备及其调形用关键零部件研究
13.The Study of Multi-Point Forming Control System Based on Parallel Mode;基于并行调形的多点成形控制系统研究
14.Development of Control System of MPF and the Modeling and Control Algorithms of Plate Forming;多点成形设备控制系统的开发及成形过程的建模与控制
15.Generating Method and Software Development for Multi-point Forming Surface Based on Triangular Mesh基于三角形网格的多点成形面生成方法与软件开发
16.Study on the relationship of technology modes and dimple of sheet metal parts in multi-point forming多点成形时工艺方式与工件压痕的关系研究
17.Several Pivotal Multi-point Forming Process and Its Numerical Simulation Study;多点成形中的几种关键工艺及其数值模拟研究
18.Research on Key Techniques of MPF-oriented Reverse Engineering and Application;面向多点成形的逆向工程关键技术及应用研究
相关短句/例句
Multi point forming多点成形
1.This paper is focused on the basic principle,forming method and the calculations of forming force and blank holder force for 630 kN multi point forming press.重点介绍了 630kN多点成形压力机的基本原理、成形方法、成形力及压边力的计算。
2.The criterion to design the transient area for sectional multi point forming is suggested.文中基于理想路径成形理论 ,提出了板材多点柔性成形最优成形路径设计的理论与方法 ,建立了多点分段成形过渡区设计准则与多点成形过程中静力隐式弹塑性大变形有限元数值模拟方法 。
3.This paper centres on performance parameters,operating principle, forming method and characteristics of the 630 kN multi point forming (MPF)press for sheet metal.重点介绍 63 0 k N多点成形压力机的性能参数、工作原理、成形方法及特点。
3)Multi-point forming machine多点成形机
4)multi-point press多点压机成形
1.Numerical simulation study on the process of multi-point press forming and multi-step multi-point die forming;多点压机成形与多道次多点模具成形的数值模拟研究
2.By contrasting the two forming modes of multi-point die(MPD) and multi-point press (MPP), The formation process of dimple and the measures to preventing dimple have been discussed in this paper, influence of different forming modes on dimple has been analyzed.本文采用有限元数值模拟手段针对多点成形过程中产生的压痕现象以及消除压痕的措施进行探讨,主要是对比多点模具成形和多点压机成形两种不同工艺,分析不同成形工艺条件下对压痕的影响。
5)multi-point die多点模具成形
1.Numerical simulation study on the process of multi-point press forming and multi-step multi-point die forming;多点压机成形与多道次多点模具成形的数值模拟研究
2.By contrasting the two forming modes of multi-point die(MPD) and multi-point press (MPP), The formation process of dimple and the measures to preventing dimple have been discussed in this paper, influence of different forming modes on dimple has been analyzed.本文采用有限元数值模拟手段针对多点成形过程中产生的压痕现象以及消除压痕的措施进行探讨,主要是对比多点模具成形和多点压机成形两种不同工艺,分析不同成形工艺条件下对压痕的影响。
6)multipoint roll forming多点滚压成形
延伸阅读
自燃点分子式：分子量：CAS号：性质：化工产品物理性能指标之一。指在规定条件下，试样在没有火焰时自发着火的最低温度。一般用摄氏温度表示。
