1)weld metal焊缝金属
1.Electrochemical corrosion properties for weld metal of austenitic stainless steel;奥氏体不锈钢焊缝金属的电化学腐蚀性能
2.Intergranular fracture of weld metal of structure steel in a ship structure at lower temperature and higher loading rate;结构钢焊缝金属在低温和动载条件下的脆断本质
3.Precipitation of Copper in High Strength SMAW Weld Metal;铜在高强度手工焊焊缝金属中的析出行为
英文短句/例句
1.all-weld-metal test specime全焊缝金属试验样品
2.Regression and Analysis on Metal Strength of Welding Seam of Welding Core Wine药芯焊丝焊缝金属强度的回归与分析
3.Superplastic Behavior of Weld Metal by Friction Stir Welding搅拌摩擦焊接焊缝金属的超塑性行为
4.Effect of Nb and V in high carbon steel weld metal铌和钒在高碳钢质焊缝金属中的行为
5.Sucking-extruding Theory for the Material Flow in Friction Stir Welds搅拌摩擦焊焊缝金属塑性流动的抽吸—挤压理论
6.Failure Analysis and Evaluation of a Low-alloyed Steel and Its Welding Metal;某低合金钢及焊缝金属失效分析及安全评定
7.Effects of Process Parameters on Flow Pattern of LY12 Aluminum Alloy during Friction Stir Welding搅拌摩擦焊工艺参数对LY12铝合金焊缝金属流动形态的影响
8.Effect of Aluminum on Microstructure and Property of Calorizing Steel Weld Metal铝对渗铝钢焊缝金属组织与性能的影响
9.J-Integral Test and Residual Strength Analysis for Steel 907A and Its Weld;907A钢及焊缝金属的J积分测试与剩余强度分析
10.Detection and Analysis of Phase Transformation Process on Weld Metal of 10CrMo910 Steel10CrMo910钢焊缝金属相变过程的实时检测及分析
11.Fracture toughness of heat-affected zone( HAZ) was between the base metal and weld metal.焊接热影响区的断裂韧性介于母材和焊缝金属之间。
12.Difference of impact absorbed energy between butt weld metal and deposited metal对接焊缝金属和熔敷金属冲击吸收功差异的探讨
13.EFFECT OF NICKEL ON SOLIDIFICATION CRACKING IN LOW C LOW ALLOY STEEL WELD METAL镍对低碳低合金钢焊缝金属凝固裂纹敏感性的影响
14.Study on the Acicular Ferrite Formation Mechanism of Weld Metal in Microalloyed Steel;微合金钢焊缝金属中针状铁素体形成机理的研究
15.Addition of activating agent has no obvious effect on fracture toughness of weld metal.添加活性剂对焊缝金属的断裂韧性没有明显作用。
16.The deposited ferritic weld metal shall not contact the austenitic or high-chromium steel cladding.熔敷的铁素体焊缝金属不应与奥氏体或高铬钢复层接触。
17.EFFECTS OF HEAT TREATMENT ON THE MICROSTRUCTURE AND MECHANICAL PROPERTY OF WELD METAL WITH Nb ADDITION热处理工艺对含Nb焊缝金属组织与力学性能的影响
18.Transfer Behavior Study in Weld Thickness Direction of the Welding Plastic Metal in Friction Stir Welding搅拌摩擦焊焊缝塑性金属在焊缝厚度方向的迁移行为研究
相关短句/例句
welding metal焊缝金属
1.In this paper,it is concluded that separated out Ti 2Ni phase is main reason of Ti31 alloy welding metal impact toughness decline by microstructure, fracture and surface.本文主要通过金相、断口、表面等分析 ,确定了Ti2 Ni相的析出是造成Ti31合金焊缝金属冲击韧性降低的的主要原因。
2.For improving the impact toughness of austenitic stainless steel welding metal in the cryogenic condition,according to the tests of some welding technologies,the effect of carbon, hydrogen and ferrite on austenitic stainless steel impact toughness at 196℃ cryogenic was disuassed and several suggestions for choosing welding metals and technologies were presented.为了提高奥氏体不锈钢焊缝金属在深冷低温条件下的冲击韧性，根据若干焊接工艺性试验，讨论了在－ 196℃条件下，碳、氢、铁素体对奥氏体不锈钢焊缝金属低温冲击性能的影响，并且提出了焊材选择的几点建议。
3)all weld metal纯焊缝金属
4)all weld metal全焊缝金属
5)weld-metal zone焊缝金属区
6)H10Mn2 weld metalsH10Mn2焊丝焊缝金属
延伸阅读
焊缝金属焊缝金属weld metal hanfeng Ilnshu焊缝金属(weld metal)金属焊接过程中被熔化而形成焊缝的金属。它是金属焊接接头的一个组成部分。若焊接过程中使用了镇充金属，则焊缝金属是熔化的母材和熔敷的填充金属的混合物，否则它仅包含熔化的母材金属。通常要求焊缝金属的力学性能与母材相匹配，而非要化学成分与母材一致。焊缝金属凝固时，沿未熔化的母材壁以树枝状或胞状结晶，使得合金元素产生偏析，导致微观上的不均匀性(与母材相比)。因此，适于母材的强化机制并不适用于焊缝金属，往往需用其他的冶金强化机制。 (李维茜)
