接头强度,Joint strength英语短句,例句大全

接头强度,Joint strength
1)Joint strength接头强度
1.The influences of welding heat input on joint strength were analyzed.采用钨极氩弧焊的方法对30%SiCP/LD2高体积分数复合材料进行了焊接实验,研究了在同种TIG焊焊接规范参数下LD2-LD2、LD2-30%SiCP/LD2、30%SiCP/LD2-30%SiCP/LD2三种不同材料组合焊接性差异,分析了焊接热输入对接头强度的影响。
2.The experimental results show that for industrial purity Ti and Ti 6Al 4V, respectively, the overlap brazing joint strength are 418.结果表明:用Ti-Cu-Ni钎料钎焊TA2和Ti-6Al-4V钛合金的搭接接头强度分别是418。
3.The temperature and time range of brazing through the wetting experiment were confirmed, and the effect of brazing conditions on the joint strength through the shear experiment was discussed.通过对钎料润湿性的研究确定钎焊试验的温度和时间范围 ;通过剪切试验研究了钎焊工艺参数对接头强度的影响。

英文短句/例句

1.Influences of adherent thickness,temperature and velocity on strength of adhesively-bonded single-lap joints板厚、温度和速度对单搭接胶接接头强度的影响
2.Study on Influence of Welding Process Parameters on Strength of Welded Joint焊接工艺参数对焊接接头强度的影响研究
3.measuring method for strength of mechanical fastenings for conveyer belts输送带机械接头强度的测定
4.Affect of Different Solder on Intension of Cu/W Brazing Joint不同焊料对Cu/W钎焊接头强度的影响
5.Ultrasoinc Nondestructive Characterization of Strength and Environmental Degradation of Adhesive Joints;胶接接头强度及环境退化的超声波无损定征
6.Influence of Interlayer's Thickness on Strength of HIP Diffusion Bonding Joints Between P/M TC4 Alloy and GCr15 Bearing Steel中间层厚度对P/M TC4-GCr15扩散焊接头强度的影响
7.STUDY ON BRAZING PROCESS AND JOINT STRENGTH OF ALUMINAC CERAMICS氧化铝陶瓷钎焊工艺与接头强度的研究
8.Analysis of Static Strength for Overlap Joint Plates and Others;搭接焊接头搭板的静强度分析及其它
9.The Strength and Loading Capacity of SSAW Pipe Welding Joint螺旋焊管焊接接头的强度和承载能力
10.Effect of Recessed Bonding on Stress Distribution and Strength of Adhesively Bonded Joints间隙连接对胶接接头应力分布和强度的影响
11.High strength joint bolts and nuts for railsGB/T5098-1985钢轨用高强度接头螺栓、螺母
12.Shear strength and fracture surface analysis of BiAgNiCuGe/CujointBiAgNiCuGe/Cu接头抗剪强度与断口分析
13.Adhesives--Determination of tensile strength of butt jointsGB/T6329-1996胶粘剂对接接头拉伸强度的测定
14.Study of the Strength and Tightness of Tube-to-Tubesheet Connection Joints;管子与管板连接接头的强度和密封性能研究
15.The Deformation Behaviors and the Strength of Welded Joints with Mechanical Properties Mismatch;力学性能失配焊接接头的强度及变形行为
16.Research on Fracture Behavior of Ultra-High Strength Steel and Welded Joint超高强度钢及其焊接接头的断裂行为研究
17.Numerical Simulation of T-welding Residual Stress and Strength AnalysisT型接头焊接残余应力数值模拟及强度分析
18.Finite Element Analysis on Lame Wave Evaluating Cohesion Strength In Adhesively-bonded Joint兰姆波评价胶接接头内聚强度的有限元分析

相关短句/例句

strength of joint接头强度
1.Effect of interfacial microstructure of TiAl/40Cr diffusion bonding on strength of joint;TiAl/40Cr钢扩散连接界面组织结构对接头强度的影响
3)bonding strength接头强度
1.The bonding strengths of joints were evaluated by shear test, and the fracture paths of joints were analyzed by SEM,EPMA and XRD.8ks的连接条件下，当连接时间较短时接头强度较高，如室温时为240MPa，高温（973K）时为230MPa，接头在（Ti5Si3CX＋TiC）／TAD界面处断裂。
2.The factors affecting the bonding strength of the joints in transport conveyer belt is analyzed, the bonding technique is introduced, and measures of improving the maintenance quality of the belt are put forward so as to extend its service life.分析影响运输皮带胶接接头强度的因素,介绍运输皮带的胶接工艺,提出提高皮带维修质量的措施,延长皮带使用寿命。
4)strength of welded joint焊接接头强度
1.An approach to evaluate the strength of welded joints with mechanical heterogeneity was proposed.提出一种评价力学性能不均匀焊接接头强度的方法。
5)butt joint strength接头(接口)强度
6)joint shear strength接头剪切强度
1.Influences of the metallizing technologic conditions, Ni plating and subsequent annealing on the joint shear strength were investigated.考察了金属化工艺、镀镍及镀后热处理对接头剪切强度和钎焊效果的影响。