齿形误差,profile error英语短句,例句大全

齿形误差,profile error
1)profile error齿形误差
1.Research on Coordinate Method for Measuring the Profile Error of Wormgears;坐标法测量蜗轮齿形误差的研究
2.Measuring the Profile Error of the Involute Gear;齿轮渐开线齿形误差的测量
3.The tooth profile error and longitudinal form error are calculated,and the change rule with setting angle of them is got.针对花键的齿形误差和齿向误差,按照误差计算原理,得出了计算结果及其随安装角改变的变化规律。

英文短句/例句

1.Research Tooth Profile Error of ZK_Worm Based on 3D Simulation;基于三维仿真ZK蜗杆齿形误差的研究
2.Application of virtual instrument technology in gear tooth error testing system虚拟仪器技术在齿形误差检测系统中的应用
3.An Algorithm for Tooth Profile Error Based on Omnipotent Gear Measuring Machine基于万能式齿轮测量机的齿形误差求解算法研究
4.Analysis of error limits for tooth profiles laid down in "Depot repair specifications for DF_4 diesel locomotive对《东风_4型内燃机车段修规程》齿形误差限度的分析
5.Amending the Shape of Pinion and Reducing the Round-gear Error;修正小齿轮表面齿形降低圆弧齿轮传动误差
6.Effect of Machine Tool Errors on the Tooth Form of Spiral Bevel Gears机床误差对螺旋锥齿轮齿形的影响规律
7.Formation Error of Archimedes Gear Hob and Its Correction阿基米德齿轮滚刀的造形误差及修正
8.The mechanical dial compartors are used for measuring the size deviation and position deviation of workpieces.详细说明：杠杆齿轮比较仪用于测量工件形状误差和位置误差。
9.Calculation of Transmission Error of Modification Double Helical Gears and Experimental Investigation修形人字齿轮传动误差计算与试验研究
10.Analysis of the Influence about Involute Cam Error to Profile Precision渐开线凸轮误差对齿形精度影响的分析
11.Measurement Error Separate and Simulation Studies for Large Gear Based on Rack-shaped-edge Probe基于刃边齿条形测头的大型齿轮在位测量的误差分离和仿真研究
12.Geometric Error Measurement of Spiral Bevel Gears and Experimental Test弧齿锥齿轮齿面误差检测与实验验证
13.The Application of Difference Surface in Deviation Characterization of Face Gear面齿轮齿面误差评定中差曲面的应用
14.gear integrated error tester齿轮整体误差测量仪
15.gear meshing error meter齿轮啮合误差测量仪
16.bevel gear integrated error tester锥齿轮整体误差测量仪
17.integrated gear error measuring technique齿轮整体误差测量技术
18.Caculation of principle error of involute profile processed by Archimedean hobbing cutter用阿基米德滚刀加工渐开线齿形的原理误差计算

相关短句/例句

tooth profile error齿形误差
1.Research on the tooth profile error of gear shaving;剃齿加工齿形误差的研究
2.Study of measurement of tooth profile error of circular tooth gears by rectangular coordinates method;用直角坐标法测量圆弧齿轮齿形误差
3.By means of analysis and calculation,the conclusion is given a spiral normal section on the pitch cylinder of a hob basic worm is different from another;If the normal sec- tion in the center of the tooth line is taken as a tooth measuring and design section,when spline hob is designed in a plane meshing,the tooth profile error is minimum.通过分析并进行计算得出:同一滚刀基本蜗杆,节圆柱上不同螺旋线的法剖面截形有明显差别;如果以齿纹中点法剖面作为齿形检测和设计剖面,用平面啮合法设计花键滚刀时,则齿形误差最小。
3)tooth profile errors齿形误差
1.On the basis of deriving the calculating formula of tooth profile error, generates a solution of the optimurn tooth profile angle, which can keep the tooth profile errors smallest.本文在推导出齿形误差计算公式的基础上,给出一种使齿形设计误差最小的最佳齿形角的求法。
4)tooth error齿形误差
1.Application of virtual instrument technology in gear tooth error testing system虚拟仪器技术在齿形误差检测系统中的应用
2.This paper presents a new method to measure tooth error of small module gears.0 mm)进行测量,提出了一种在视觉三坐标测量机上测量小模数齿轮齿形误差的新方法。
5)tooth form error齿形误差
1.On-machine measuring method of tooth form errors of spiral bevel gears was investigated.对大规格螺旋锥齿轮齿形误差的在机测量方法进行了研究。
2.Non - zero orthogonal rake hobbing cutter produces large error by common grinding ways accoding to the chamge of tooth form error.非零前角滚刀按常规方法重磨产生较大齿形误差，本文根据重磨齿形误差变化规律，用优化方法确定滚刀重磨参数，控制误差，提高滚刀重磨精度，增加滚刀的精度寿命。
6)total profile error齿形误差
1.Using a four-dimensioned universal installation with high precision that can control and measure temperature,an experiment program is designde in particular condition to measure the total profile error changed with temperature.齿轮在工作温度和环境温度偏离标准温度后,其齿形会发生改变,引起齿形误差,而齿形误差又是影响齿轮传动平稳性的重要因素之一。