1)impression taking取模
英文短句/例句
1.A Research about the Pattern Acquisition for Free Text IE;自由文本的信息抽取模式获取的研究
2.Automatic Acquisition of Information Extraction Patterns Based on Bootstrapping基于自扩展的信息抽取模式自动获取
3.Failed to read template file. Using generic template.读取模板文件失败。请使用一般模板。
4.Parameter Model Extraction of 0.8 Micron CMOS/SOI Technology0.8μm CMOS/SOI模型参数提取
5.This template supercedes all the templates in the following list.这个模板取代所有下列表中的模板。
6.Christian: My recent developments: undo and the plugin mechanisms, both via Design Patterns.设计模式中学习到的“取消”和插件模式。
7.Practice taking impression for plaster models two pairs,?练习取印模、灌石膏模型二付，装石膏托。
8.Research and Simulation of Short Fibre Orientation in Compression Molding of SMC;SMC模压流动中纤维取向的研究与模拟
9.Deep Web Form Schema Extraction and Schema IntegrationDeep Web入口模式抽取与模式集成
10.Model Reading from 3DS File and Displaying in OpenGL Mode3DS模型的读取与OpenGL模式下的显示控制
11.Templates that appear in the global templates list (template picker).出现在全局模板列表中的模板（模板选取）。
12.A Further Discussion of Max-Min Algorithm in Fuzzy Synthetic Evaluation;模糊综合评判取大取小算法问题的进一步讨论
13.Fuzzy Relation Geometric Programming with Max-product Composition;具有取大取小合成算子的模糊关系几何规划
14.Forensic Analysis of Network Intrusion and Research on the Modeling for Network Intrusion Forensic System;网络入侵的取证分析及取证系统建模研究
15.Simulation Study on Preparation of Anhydrous Isopropanol by Extractive Distillation Using Dividing Wall Column隔壁塔萃取精馏制取无水异丙醇的模拟研究
16.On the Journals Publishing Modes and Their Access Under the Open Access Environment开放存取期刊的出版模式及其“获取”途径
17.In reference[1], the properties of fuzzy measure and fuzzy integrals of the abstractfunction were investigated.文[]引入了取值向量格的模糊测度和模糊积分。
18.The mold cavity was obtained by splitting mold base in parting surface.模具型腔可采用分型面分割模板的方法获取。
相关短句/例句
coiling model卷取模型
3)uptake mode摄取模式
1.The degradation ability and uptake modes of Long-chain alkane-degrading bacteria were investigated.对长链烷烃降解菌的降解能力和摄取模式进行了研究。
4)reorientation model取向模型
5)model of uptake摄取模型
6)oriented molding取向模压
1.Poly(lactic acid) plates for internal fixation of bone fractures were prepared with poly(DL-lactic acid)(PDLLA),poly(L-lactic acid)(PLLA) and their mixture through oriented molding respectively,and the mechanical performances of the plates were tested.分别以左旋聚乳酸(PLLA)和消旋聚乳酸(PDLLA)以及两者的共混物为原料,采用取向模压法制备了聚乳酸(PLA)骨折内固定板材,并考察板材的力学性能。
延伸阅读
凹模、凸凹模工作型面加工工艺过程1)备料。 n 2)锻造。锻成长方形的坯料(每件留长工艺夹头)。 n 3)热处理。退火。 n 4)铣(刨)削。铣(刨)削六面成长方形模块。 n 5)磨削。磨削上、下两端面及相邻两侧面，用90。角尺测量相邻两面的垂直度。 n 6)钳工加工。用平板和划线盘按图划线，并打样冲眼；用钻头钻螺纹底孔；用圆柱销孔的预孔；用钻头钻挡料销让位孔；用钻头在中心处钻穿丝孔等；正、反面孔口倒角；凸凹模用钻头孔扩，保证刃口高度；攻螺纹；铰孔。n 7)铣削。平口钳装夹工件；用的立铣刀铣削型孔至尺寸，保证深度。 n 8)热处理。凹模工件淬硬至HRC60～64，凸凹模工件淬硬至HRC58～62。 n 9)平磨。磨上、下两端面及相邻两侧面，用90。角尺测量相邻两面的垂直度至图要求；退磁。 n 10)线切割。按图编制线切割程序，切割模型孔成形，留单面研磨余量0.005 mm。 n 11)钳工加工。研光线切割面： n 12)检验。 n复合冲裁模的装配应选择凸凹模作为装配基准件，先装下模部分，后装上模部分
