曲轴-轴承系统,Crankshaft-bearing system英语短句,例句大全

曲轴-轴承系统,Crankshaft-bearing system
1)Crankshaft-bearing system曲轴-轴承系统
1.Multidisciplinary coupling among dynamics,tribology and elastic mechanics(strength and stiffness of crankshaft) of the crankshaft-bearing system of a four cylinder diesel engine was studied by considering the misalignment caused by the elastic deflection of the crankshaft,ADAMS and ANSYS special software were used to solve the coupling problem.采用动力学仿真软件ADAMS和有限元分析软件ANSYS,辅以手工编程相结合的方法,研究了计入曲轴倾斜时某4缸柴油机曲轴-轴承系统动力学、摩擦学和弹性力学(曲轴的刚度和强度)耦合分析问题。

英文短句/例句

1.Coupling Analysis of Dynamics Tribology and Elastic Mechanics for a Crankshaft Bearing System计入曲轴倾斜时曲轴-轴承系统动力学摩擦学和弹性力学耦合分析
2.Coupling Researches on Tribological and Dynamical Behaviors of the Crankshaft-Bearing System of Internal Combustion Engines;内燃机曲轴-轴承系统摩擦学动力学耦合研究
3.Coupling Research on Tribology, Stiffness and Strength of Crankshaft-bearing System;曲轴—轴承系统摩擦学、刚度和强度的耦合研究
4.upper center crankshaft bearing曲轴主轴承上中轴瓦
5.Analytical Investigation on Strength and Main Bearing Lubrication of CA4D32 Diesel Engine Crankshaft System Based on a Simulation Technique;柴油机曲轴轴系强度和主轴承润滑仿真研究
6.Modeling for Rotor System of AC Magnetic Bearing Electric Spindle;交流磁轴承支承电主轴转子系统建模
7.Coupling Researches on Dynamics Tribology Stiffness and Strength in the Crankshaft-Bearing System of Internal Combustion Engine;内燃机曲轴—轴承系统动力学摩擦学刚度和强度耦合研究
8.The feed holes for the crankshaft main bearings.曲轴主轴承进入口。
9.Crankshaft and main bearings service曲轴和主轴承的维修
10.Positive crankcase ventilation (PCV)积极式曲轴箱通风系统
11.crankcase emission control system曲轴箱排放物控制系统
12.The Monitoring System of Orbit of Shaft Center of Active Magnetic Bearing Based on LabVIEW基于LabVIEW的磁力轴承轴心轨迹监测系统
13.The crankcase ventilation system carries fresh air through the crankcase.曲轴箱通风系统要携带新鲜的空气通过曲轴箱。
14.Emulation and Caculation of Hydroelectric Generation Set Shafting Base on Rotor Bearing System;基于转子轴承系统的水轮机主轴系统仿真计算
15.Dynamic Behavior of a shaft-rolling bearing system with clearance计入轴承间隙时轴-滚动轴承系统动力学行为研究
16.Precise determination of windings axes angle and model stiffness coefficients for bearingless motors无轴承电机绕组轴线及控制系统刚度系数测定
17.Development of the Recognition System for output Shaft Type of Gasoline Engine Crank;汽油发动机曲轴输出轴类型识别系统的研制
18.Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.曲轴上的导向轴承:曲轴上的导向轴承一般或者是轴瓦,或者是球轴承。

相关短句/例句

Crank shaft rotor-bearing system曲轴转子-轴承系统
3)flexible crankshaft bearing system弹性曲轴-轴承系统
4)shaft-bearing system轴-轴承系统
1.Multidisciplinary coupling analysis on dynamics,tribology, strength and stiffness for a shaft-bearing system was studied herein,considering misalignment caused by shaft deformation on variable load.采用动力学仿真软件ADAMS和有限元分析软件ANSYS,辅以手工编程的方法,研究了变载荷作用下轴-轴承系统动力学、摩擦学、刚度和强度耦合分析问题的建模和求解,着重讨论轴受载变形倾斜对轴-轴承系统动力学行为、轴承的摩擦学特性和轴颈表面动应力的影响。
2.Based on the dynamics for multiple flexible bodies of an elastic shaft and its tribological characteristics,dynamic problem for the elastic shaft-bearing system with misaligned journal is solved on sine load.以弹性轴的多柔体动力学理论为基础,通过ADAMS软件进行动力学仿真,解决了考虑轴承摩擦学特性和轴受载变形倾斜时弹性轴-轴承系统在正弦激励力作用下的动力学求解问题。
3.On the basis of analysis of dynamics for multi-flexible bodies,the dynamic and tribological behaviors of the flexible shaft-bearing system under a shock load are studied with the combining simulation of ADAMS and Matlab,considering shaft misalignment caused by elastic deflection of shaft.以多柔体动力学分析为基础,通过ADAMS与Matlab联合仿真,研究在冲击激励力作用下计入轴受载变形倾斜时弹性轴-轴承系统的动力学和摩擦学行为。
5)Shaft-bearing system轴轴承系统
6)bearing system轴承系统
1.The internal heat sources of bearing system is analyzed.以热连轧机轴承系统的热效应问题作为研究对象,详细分析了轴承系统的内热源和轴承摩擦力矩的两种计算方法,最后阐述了影响轴承温升的其它相关因素。
2.The internal heat sources of bearing system is analyzed, Morever, two methods for calculating the friction heat are introduced.以热连轧机轴承系统的热变形故障作为研究对象 ,详细分析了轴承系统的内热源和轴承摩擦力矩的两种计算方法 ,最后采用PALMGREN公式计算了不同转速下的轴承温
3.In allusion to the specific features of a nonlinear rotor bearing system, the nonlinear vibration of an elastic rotor bearing foundation system on the assumption of short bearing model is formulated and its characteristics are studied in some parameter ranges based on rotor dynamics and nonlinear dynamics theory with the Poincaré maps and numerical integral method.以转子动力学和非线性动力学理论为基础 ,针对非线性转子 -轴承系统的具体特点 ,建立了采用短轴承模型的弹性转子 -轴承 -基础系统模型 ,并用数值积分和庞加莱映射方法对其在某些参数域中进行了非线性振动研究。