气流干燥,Pneumatic drying
1)Pneumatic drying气流干燥
1.Computer simulation of pneumatic drying wet alumina particulates in a vertical pipe;直管气流干燥氧化铝过程计算机仿真
2.Numerical simulation of heat and mass transfer in pneumatic drying process of wet alumina particles气流干燥含湿氧化铝颗粒传热传质数值模拟
英文短句/例句

1.Design of Dryer by Air Flow Drying System for Tobacco烟丝气流干燥系统气流干燥器的设计
2.The Design and Application of Pulsed Pneumatic Dryer for Ketogulonic Acid;古龙酸脉冲气流干燥器的设计与应用
3.Operation and Structure Optimization of Impulse Pneumatic Dryer by Simulation;脉冲式气流干燥器的操作与结构优化模拟研究
4.Numerical simulation of heat and mass transfer in pneumatic drying process of wet alumina particles气流干燥含湿氧化铝颗粒传热传质数值模拟
5.single-stage pneumatic conveyor dryer单段气流输送干燥器
6.Experimental Investigation on Drying Characteristics of Gas-Solid Stirred Fluidized Bed;气固搅拌流化床的干燥特性实验研究
7.Hydrodynamics of Centrifugal Fluidized Beds and Thermal Analysis of Drying Process;气固离心流化床动力学及干燥过程热力分析
8.Effect of Air Flow Rate and Air Temperature on Wood Drying Rate;空气流速和温度对木材干燥速率的影响
9.Comparison study of working medium of refrigeration cycle applied on fluidized-bed freeze-dryer流化床冷冻干燥气体制冷循环工质的比较研究
10.Coupling Process Analysis for Granular Ammonium Phosphate Production by Fluidizing Ammonification and Granulation with Tail Gas Recycling磷铵尾气循环-流化氨化-干燥结晶耦合过程分析
11.Drying Monukka grapes with air-impingement jet technique and quality analysis气体射流冲击干燥无核紫葡萄及品质分析
12.Study on the Parameters of Pneumatic Spray Drying of Feeding Protease Fermentation Liquid饲用蛋白酶发酵液气流式喷雾干燥参数研究
13.That state has a dry climate in winter.该州冬天气候干燥。
14.unheated air dryer未加热空气式干燥器
15.drying air temperature control干燥用空气温度调节器
16.The climate is very dry in the desert area.沙漠地区气候很干燥。
17.vibrating fluidized bed dryer振动式流化床干燥器
18.In many kilns the air flow can be reversed in order to reduce these differences.许多干燥窑内的空气是可以反向流动的,为的是减少这种差异。
相关短句/例句

Gas flow drying气流干燥
1.The numeral solution of the mathematical simulation equation stood for gas flow drying process of Pseudo-boehmite was obtained by using the standard four-step Runge-Kutta method in Matlab software.对已建立的拟薄水铝石直管气流干燥系统数学模型,采用Matlab语言调用标准四阶Runge Kudra法进行数值模拟,给出高精度的数值解,现有烘干机的测试实验表明模拟结果与测试数据一致。
2.The numeral solution of the mathematical simulation equation stood for gas flow drying process was obtained by the standard fourstep RungeKudra method.通过分析气流干燥的特点,建立的直管气流干燥模拟方程,采用Matlab语言调用标准四阶Runge-Kudra法,给出高精度的数值解。
3)flash drying气流干燥
1.According to the principle of flash drying,the domestic gluten flour drying system was analized systematically and the improvement of the key equipment.根据气流干燥原理,针对国内谷朊粉干燥系统存在的能耗高,活性差,产量低等缺点,对该系统做了相关分析,并和生产实践相结合,提出了改进方法。
4)flash dryer气流干燥
1.This paper introduces the copper concentrate drying technology in Flash Smelting processes,and compares characteristic and application status between the flash dryer and steam dryer,the result makes know that the steam dryer has evident advantage in terms of equipment investment,energy consumption and environment protection,it is provided with extensive use.介绍了目前闪速熔炼生产中常用的铜精矿干燥技术,并给合应用状况,对2种干燥技术——气流干燥和蒸汽干燥进行了对比,结果表明,蒸汽干燥技术在设备投资、节能与环保方面有着明显的优势,具有推广价值。
5)HXD pneumatic dryingHXD气流干燥
6)flash dryer气流干燥器
1.Mathematical model and design calculation method separated section of flash dryer;气流干燥器数学模型及分段设计计算方法
延伸阅读

气流干燥  将散粒状固体物料分散悬浮在高速热气流中,在气力输送下进行干燥的一种方法。由于气体相对于物料颗粒的高速流动,以及气固相间接触面积很大,体积传热系数相当大,比常用的转筒式干燥器大20~30倍。气流干燥适合于处理粒径小、干燥过程主要由表面气化控制的物料。对于粒径小于0.5~0.7mm的物料,不论初始含水量如何,一般都能将含水量降为0.3%~0.5%。但由于物料在气流干燥器内的停留时间很短(一般只有几秒),不易得到含水量更低的干燥产品。如果有必要,则需后续其他低气速运行的干燥器。    气流干燥器(见彩图)主要由干燥管、旋风分离器(见离心沉降)和风机(见流体输送机械)等部分组成(见图)。湿物料经加料器连续加至干燥管下部,被高速热气流分散,在气固并流流动的过程中,进行热量传递和质量传递,使物料得以干燥。干燥了的固体物料随气流进入旋风分离器,分离后收集起来,废气经风机排出。由于物料刚进入干燥管时上升速度为零,此时气体与颗粒之间的相对速度最大,颗粒密集程度也最高,故体积传热系数最高。在物料入口段(高度约为1~3m),气体传给物料的热量可达总传热量的1/2~3/4。在入口段以上,颗粒与气流之间的相对速度等于颗粒的沉降速度(见沉降),传热系数不很大。因此,入口段是整个气流干燥器中最有效的区段。    气流干燥器的主要缺点在于干燥管太高,为降低其高度,近年来出现了几种新型的气流干燥器:①多级气流干燥器。将几个较短的干燥管串联使用,每个干燥管都单独设置旋风分离器和风机,从而增加了入口段的总长度。②脉冲式气流干燥器。采用直径交替缩小和扩大的干燥管(脉冲管),由于管内气速交替变化,从而增大了气流与颗粒的相对速度。③旋风式气流干燥器。使携带物料颗粒的气流,从切线方向进入旋风干燥室,以增大气体与颗粒之间的相对速度,也降低了气流干燥器的高度。    在气流干燥器中,主要除去表面水分,物料的停留时间短,温升不高,所以适宜于处理热敏性、易氧化、易燃烧的细粒物料。但不能用于处理不允许损伤晶粒的物料。目前,气流干燥在制药、塑料、食品、化肥和染料等工业中应用较广。