1)flow passage components过流部件
1.Optimization design of flow passage components in cleaning robot and analysis of its inner flow清洗机器人过流部件流动分析与优化设计
英文短句/例句
1.Hydraulic Design of Water-passing Components of Hydraulic Turbines with 230 m Water Head230m水头段水轮机过流部件水力设计
2.Optimization design of flow passage components in cleaning robot and analysis of its inner flow清洗机器人过流部件流动分析与优化设计
3.Study of Casting-Infiltration of Boron on Local Surface of Fluid-flow Components of Large Water Pumps;大型水泵过流部件局部表面铸渗硼技术的研究
4.Optimum Design and Vibration Characteristics Analysis of Hydraulic Turbine Components;水轮机过流部件的优化设计和振动特性分析
5.Preliminary analysis on abrasion of turbine's flow parts of TGP's power station on left bank三峡左岸电站水轮机过流部件磨蚀初析
6.Numerical Simulation of the Sandy Ablation of Centrifugal Pump Impeller Flowed Passage Parts in High Sandy Flow;含沙水流中离心式水泵过流部件泥沙磨损的数值模拟
7.Research on material flow trait during cross wedge rolling process楔横轧变形过程中轧件内部金属流动的规律
8.In-line flow restrictor protects the meter measuring element and the backflow preventer components from damage due to excessive flow.管内流量限制器保护仪表测量元件和防回流阀部件不会因为过大的流量而受到损坏。
9.The two-way flow principal is based on crossflow filtration separation utilising“ inside-out” flux and allowing the inside of the hollow fibers to build up with pollutant/ concentrate particles.在双向流膜过滤操作的第一阶段，原液从膜组件下部进入，回流浓缩液从上部流出。
10.Parallel circuit: A circuit in which all the parts are connected to the same voltage but the current divides between them and later re-unites.并联电路:电路内的各部件都连于同一的电压上，但电流于各部件间分开，过后再汇合。
11.A type of sculpture consisting of carefully equilibrated parts that move, especially in response to air currents.可动雕塑一种由经仔细设计达到平衡的部件组成的雕塑，气流通过时部件会运动
12.Fluids and mineral interactions in extreme conditions of the Earth interior:In-situ observation of the deep Earth fluids using diamond anvil cell地球内部极端条件下流体和物质相互作用:透过金刚石窗口探测地球深部流体
13.A system flowchart uses symbols to represent programs, procedures, hardware devices, and the other components of a physical system (Fig. 9.4.).系统流程表示程序、过程、硬设备及物理系统中的其它部件（图9.4）。
14.An example of engine crankshaft was used to illustrate application of the new method.以发动机曲轴部件为例，叙述了设计流程的应用过程。
15.Polymer filter/elements/fibermets聚合物过滤器/部件/滤芯
16.The coat has a mend on the elbow.这件外套的肘部补过。
17.to go on to visual display units,通过直观显示部件，
18.Magnetic lines of force (or flux) can be set up by passing a large current of electricity through the component to be inspected, by use of a magnetizing yoke, and by use of a magnetizing coil.用大电流通过被测部件并用磁轭和用磁化线圈可以产生磁力线(或磁流)。
相关短句/例句
hydraulic turbine flow-parts水轮机过流部件
1.The wear-corrosion and surface prevention of hydraulic turbine flow-parts;水轮机过流部件的磨蚀与表面防护
3)filter elements过滤部件
1.The efficient, economic and environment friendly cleaning of sensitive parts like spinnerets, filter elements etc.现代化的生产工厂有必要拥有高效、经济、环境友好的清洗工艺来清洗喷丝板、过滤部件那样的热敏部件。
4)transflux part过流件
1.Characteristic anlysis and material selection of high chromium cast iron for transflux parts of slurry pump;渣浆泵过流件用高铬铸铁材料特性分析与选择
5)part stream零部件流
6)magnet part磁流部件
1.The problem discrimination of the VG354 MS magnet part DAC was introduced,and also a new measureing method through varing accelerating voltage with special for the DAC was devoloped which soloved the measuring diffculties of some isotopes such as U and Pb because of the DAC trouble.本文介绍了对ＶＧ－３５４质谱仪磁流部件ＤＡＣ出现的故障所进行的诊断，同时针对故障现象建立了一种改变加速电压的测量方法，解决了因ＤＡＣ出故障而使Ｕ、Ｐｂ等同位素无法测量的问
延伸阅读
将UG里的一个装配部件输出成单个部件文件法一： 关闭（turn off）FileàOptions->Load Options下"Partial Loading "选项 打开装配部件 选择File->Export->Part 在"Part Specification"下选择"new" 选择"Specify Part"，指定输出部件文件名称及位置 将"Object Selection Scope"设定为"All Objects" 选择"Class Selection->Select All"高亮所有对象 按"OK" 该种方法特点：每一个部件的特征都会汇集在新部件的MNT里。可以方便编辑。法二：闭（turn off）File->Options->Load Options下"Partial Loading "选项 打开装配部件 Application->Assembly Assemblies->Components->Create New，给出想要输出的部件文件名及路径。 如下图1，在ANT上双击新产生的部件文件，使其成为工作部件。 Assemblies->WAVE Geometry Linker，将设置改为"Body"，选择所有组件的体。 将"Create Non-associative"开关设为"On"，见下图2 将产生的部件设成显示部件，仅保存刚产生的新部件，不保存旧的装配部件。
图1
图2 该种方法特点：每一个部件在新部件的MNT里只会显示一个link的特征。没有相应特征可以编辑。
