1)running-in wear磨合磨损
1.The worn surfaces,fractal of surface and interface as well as fractal model of running-in wear for the application of fractal theory in tribological research were investigated.对近年国内外分形理论在摩擦学研究中应用的新进展作了综述,介绍了分形的概念以及分形维数的计算方法,讨论了包括磨损表面形貌分析,材料表界面分形研究和磨合磨损分形模型的建立等分形理论在摩擦学研究中的应用状况,并提出了当前相关研究中所遇到的问题,及今后分形理论在摩擦学研究中的发展方向。
2.The running-in wear test for materials of crankshaft journal against bearing shell of S50MC marine diesel engine has been conducted by a ring-on-disc tester in this paper.采用环-盘摩擦磨损试验机进行S50MC型船用柴油机曲轴颈-轴瓦材料配副磨合磨损试验,通过对摩擦系数、磨损失重量及磨损表面形貌的分析,研究了不同轴向载荷对AlSn40合金轴瓦磨合磨损性能的影响。
英文短句/例句
1.The Study on Running-in and Wear Properties of Crankshaft-bearing Shell of Diesel Engine柴油机曲轴-轴瓦磨合磨损性能研究
2.worn clutch facing磨损的离合器摩擦片
3.The wear mechanism of stainless steel against copper based sintered alloy is mainly attributed to adhesion,abrasion and oxidation.不锈钢/铜基烧结合金材料的磨损机制主要是粘着磨损及氧化磨损。
4.These three kinds of debris indicate that the wear between liner and piston is a composite form of fatigue wear, adhesive wear and abrasive wear.这三种磨屑的存在表明这对摩擦副间的磨损是疲劳磨损、粘着磨损及磨粒磨损等所形成的综合磨损。
5.A Study on Impact Abrasive Wear Resistance and Wear Mechanism of Fe-B-C AlloysFe-B-C合金冲击磨料磨损性能及磨损机制的研究
6.A Study of Low-stress Washing Abrasive Wear of W-alloy White Cast Irons钨系合金白口铸铁低应力冲蚀磨料磨损的研究
7.Anti-abrasive Wear Composite of Carbide Eutectic/Cu-Mn-Ni Cupronickel;碳化物共晶体/锰白铜抗磨料磨损复合材料
8.The Tribological Performance for the Thermoplastic Polyimide Composites;热塑性聚酰亚胺复合材料的磨擦磨损性能
9.Research on Micro-scale Abrasive Wear of TZNT Titanium Alloys in Simulated Body Fluid Environment;模拟体液环境下TZNT钛合金微磨粒磨损研究
10.Research on Micro-scale Abrasive Wear of TLM Titanium Alloys in Simulated Body Fluid Environment人体腐蚀环境下TLM钛合金的微磨粒磨损研究
11.Study on Abrasive Resistance of Haystellite7 Alloy Coating Prepared by Flame Remelting火焰喷熔Haystellite7合金涂层耐磨粒磨损性能研究
12.Micro-abrasion Performances of TAMZ Alloy in Simulated Body Fluid模拟体液环境下TAMZ合金的微磨粒磨损行为研究
13.An Information Fusion Technique for Wear Particle Recognition Based on Neural Network基于神经网络信息融合的发动机磨损磨粒识别
14.rotary abrasive tester旋转式磨料磨损试验机
15.A frayed or tattered condition.磨损磨破或破烂的状态
16.Grain-abrasion Behaviour of Wear-Resistant Steel BHARDY耐磨钢BHARDY的磨粒磨损行为
17.The bulk deformation, fatigue and plough were the major wearing mechanism.结果表明:合金的主要磨损机制是体积塑性变形、沟效应和疲劳磨损。
18.Wear property and mechanism of laser cladding TiC-Ni composite coating激光熔覆TiC-Ni复合涂层的摩擦磨损性能和磨损机制研究
相关短句/例句
wear and running-in磨损磨合
3)synergic wear复合磨损
1.On the basis of analyzing typical impact erosion and cavitations erosion test equipment and methods in sandy environments,in view of the special wear patterns in our national hydraulic machinery and hydraulic architecture,a new type of water jet test equipment and method that can be applied to study submerged synergic wear of impact erosion & cavitations erosion was introduced.在分析典型含沙水流的冲蚀、气蚀磨损试验设备和方法的基础上,针对我国水力机械和水工建筑的特殊损伤破坏形式提出了基于射流的水下冲蚀与气蚀复合磨损试验设备和方法。
4)Occlusal attrition(牙合)磨损
5)mixed abrasion混合磨损
6)meshing wear啮合磨损
延伸阅读
磨合 在机器装配后使用前，为了使配合件正常稳定运转的一种措施，也称跑合。磨合是一种有意安排的磨损过程。机械零件的磨损过程一般包括磨合阶段、稳定磨损阶段和剧烈磨损阶段(见图)。OA为磨合阶段。机器开动后，磨损率(即OA曲线的斜率)从大逐渐减小。这是由于摩擦副表面微观凹凸不平，开始时实际接触面积很小,接触应力很大。在磨合过程中,较软的零件表面材料发生塑性流动，使接触面积扩大并出现加工硬化层。对于较硬材料，高的微凸体被磨去，表面逐渐变得平坦而使接触面积增加。这些变化使以后的磨损率减小而达到磨合目的。磨合应由轻到重缓慢加载，并保持润滑油的清洁，防止磨屑进入摩擦面而造成剧烈的磨损和发热。在磨合过程中须严密注意运转情况（听声、测温等）。磨合结束后应仔细清洗并换用新的润滑油。
