DOE,design of experiment英语短句,例句大全

DOE,design of experiment
1)design of experimentDOE

英文短句/例句

1.DOE Optimization was applied on Twist Beam Suspension to Improve Ride and Handling基于操纵稳定性的扭转梁悬架DOE优化
2.Application of DOE on Quality Improvement in SMT Screen PrintingDOE在SMT丝网印刷中质量改进的应用
3.Coniform Piston Pin Bore Design in DOE Method使用DOE方法进行活塞异型销孔设计
4.The Application Research of DOE in the Optimal Design of Band-pass Filter CircuitDOE在有源滤波器优化设计中的应用研究
5.The Research on the Application of DOE in the Process Optimization and Circuit Optimal DesignDOE在工艺优化和电路优化设计中的应用研究
6.Defect Solution of Gas-Assisted Molding for Thick-Wall Plastic Part Based on DOE基于DOE厚壁零件气辅成型缺陷的解决途径
7.Research on Electroluminescent Lamp Inner Short Circuit Detection Based on Shainin DOE基于谢宁DOE的背光灯片内部短路侦测研究
8.DOE Optimization Design of Structure Parameters of Bus Air Suspension Based on ADAMS基于ADAMS的客车空气悬架结构参数DOE优化
9.Molding Parameter Optimization for Injection Color and Gloss Based on Minitab DOE基于Minitab DOE的注射颜色和光泽度的成型参数优化
10.Optimization process of crankshaft induction hardening by design of experiment(DOE)用试验设计(DOE)法优化曲轴感应淬火工艺
11.Color and Gloss Control of Surface of Molded Part Based on DOE基于DOE的注射零件表面颜色和光泽度的控制
12.Optimal Design of Passive Flow Control for Ultra-compact Inlet using Design-of-Experiment基于DOE方法超紧凑S型进气道被动流动控制优化设计
13.Application of DOE on Parameter Optimization in PCB Micro-drilling Process实验设计(DOE)技术在PCB微孔钻削工艺参数优化中的应用
14.Application of DoE in Common Rail Diesel Engine Optimization DesignDoE在高压共轨柴油机优化设计中的应用

相关短句/例句

DOE-2 programDOE-2程序
1.Using the DOE-2 program developed by Lawrence Berkeley National Laboratory as calculation core, analyzing the influence of floor height and total architectural height for building shape coefficient in the region cold in winter and hot in summer, th.应用美国劳伦斯伯克力国家实验室(LawrenceBerkeleyNationalLaboratory)开发的DOE-2程序为计算内核,分析住宅建筑层高、建筑总高度对冬冷夏热地区不同形式建筑的体形系数的影响,进而研究其对建筑采暖能耗、空调能耗和建筑总能耗的影响。
3)DOE analysisDOE分析
4)DOE-2 simulationDOE-2模拟
5)DO E reportDOE报告
6)DOE experimentDOE试验
1.The optimum conditions(foaming temperature 115℃,saturatio pressure 15MPa and foaming time 1s ) were obtained according to DOE experiments results to achieve high open cell degree(61.本课题首先以纯PLA为基体,采用快速降压法,运用DOE试验研究了三个主要工艺参数发泡温度、饱和压力和发泡时间对发泡过程的影响,并确定了试验空间内获得较高开孔度和较小表观密度的最佳工艺条件为发泡温度115℃、饱和压力15MPa、发泡时间:15s,在该工艺条件下获得了开孔率61。
2.Gas-assisted molding parameters were opbimjzed by DOE experiments,through sorting the number of factors and their levels,the designed fit models were built and residuals were analyzed.将DOE试验设计引入气辅注塑成型参数配置和优化中,通过遴选试验因子及其水平数量拟合选定模型,进行残差分析,优化成型参数,并用试验验证该方法可有效地消除注射缺陷。