充液率,filling rate英语短句,例句大全

充液率,filling rate
1)filling rate充液率
1.Experimental study on the working fluid filling rates of a special separate type heat pipe;分离式热管充液率实验研究
2.The heat transfer characteristics of mini flat heat pipes with acetone,ethanol and water as the working fluid and their filling rate 20%~90% were studied.以丙酮、乙醇和水为工质,对小型平板热管在充液率为20%~90%的传热性能进行了实验研究。
3.The results show that the optimum inclination angle of the component is 30°,its filling rate is 18%.确定了新型复合工质元件的最佳倾角为30°和充液率为18%。

英文短句/例句

1.the optimal inclination angle is from 70° to 90°and the optimal charging ratio is around 50%;最佳倾角为70°~90,°最佳充液率在50%左右;
2.Effect of Inclination Angle and Liquid Filling Ratio on Operation Performance of Pulsating Heat Pipes倾斜角及充液率对脉动热管运行性能的影响
3.expansion ratio充气率，发泡率膨胀率
4.capital adequacy ratio (CAR) requirement资本充足比率要求,资本充足比率规定
5.To fill to excess, as with blood or other fluid.使充血充溢过量，如充血或充胀其它液体
6.Dialysis adequacy of patients who used silicone dual-lumen catheter with a Dacron cuff and comparison of infection rate between these dialysis patients and CAPD patients.带涤纶套经隧道双腔导管为通路血液透析患者透析充分性及与腹膜透析患者感染率比较
7.rehydration/nutrition centre体液补充／营养中心
8.nondamaging gravel packing fluid不污染的砾石充填液
9.electrolytic battery charger电解液蓄电池充电器
10.maximum allowable tank filling limit最大允许液舱充装数量
11.hydrodynamic unit change pressure液力传动装置充油压力
12.To supply or charge(liquid) with a gas, especially to charge with carbon dioxide.充气于充气于（液体），特指用二氧化碳充气
13.permeability of tunnel fill material炮眼充填材料的渗透率
14.machine hour plus supplementary rate method机器小时加补充率法
15.swelling up with blood or other fluids (as with congestion).阻塞时充满血液或其他液体的膨胀。
16.Effects of dialysate flow rate on dialysis adequacy in patients with maintenance hemodialysis透析液流量对血液透析充分性的影响
17.Trouble Analysis of Prefill Valve for Model of YX27-5000 Hydraulic PressorYX27-5000型热模液压机充液阀故障分析
18.Calculation of Packing Fraction and Packing Efficiency of Optical Fiber Bundle光纤传光束敛集率及其填充率的计算

相关短句/例句

filling ratio充液率
1.The thermal performances of plate heat pipe with open triangular (swal1ow-tailed) grooves,including the effects of inclination, filling ratio and groove construction, are investigated.本文对具有燕尾形(开式三角形)轴向槽道的微小型铜—水平板热管的传热性能,以及热管的倾角、充液率和槽道结构对其性能的影响进行了实验研究。
2.The paper investigates the discrepancy between technical & industrial applicability of heat pipe exchangers in building heat recovery and energy conversation, systematically analyses the universal engineering problems in the design of energy-saving engineering, such as structural style, material option, working fluid and filling ratio, and so on.考察热管换热技术在建筑热回收及节能中的技术适用性及其与工业应用的差异;对节能工程设计中的热管换热器结构形式、材料选择、最佳充液率等一般性工程问题作了系统分析,为实际设计提供方法论指导。
3.Based on experimental data, empirical correlation on filling ratio was obtained via regression.根据试验数据拟合出合理充液率的经验关系式。
3)charging ratio充液率
1.Studies the impact of charging ratio on heat transfer effect and seeks the optimal ratio.设计了分离式热管热回收样机,通过实验分析了热管热回收效率随室内外温度的变化规律,探讨了充液率对热管传热效果的影响以及最佳运行工况下的充液率。
2.And the relations between heat transfer rate and charging ratio, cooling, method, relative position of heating end and cooling end etc was investigated; On the basis of experimental result, some elemental problem about running of PHP was discussed and aanalized.本文对回路型脉动热管（ＬｏｏｐｅｄＰＨＰ）的运行进行了可视化实验研究，观察了其稳定运行时，工质的运动特征和热管内的典型现象；研究了其传热性能与充液率，冷却方式，加热端与冷却端相对位置等各种因素的关系；在可视化实验结果的基础上，对脉动热管运行的一些基本问题进行了讨论和分析。
4)liquid-filled ratio充液率
1.The effect on heat transfer performance caused by heat flux,gradient and liquid-filled ratio of evaporation end was deeply investigated.分析了热管的启动特性以及热流密度、蒸发段倾角和充液率对其传热特性的影响。
5)liquid filling ratio充液率
1.Adopting R123 as the working medium,the effects of liquid filling ratio and heating mode on heat transfer limit were qualitatively analyzed on the open loop pulsating heat pipes test fig consisted of 40 elbows bent by fine copper tubes with inner diameter of 1 mm and 2 mm,and the experimental values were compared with calculated values by the Katpradit\'s correlations for heat transfer limit.在由内径分别为1 mm和2 mm的细铜管弯曲而成的2组40弯头开式回路脉动热管试验装置上,采用R123为工作介质,定性分析了充液率及加热方式对传热极限的影响,并将试验值与Katpradit传热极限关联式的计算值进行了比较,结果表明:随着充液率的提高,传热极限先增大而后减小,存在一个最佳充液率(约50%);在3种加热方式中,垂直底部加热有助于脉动热管取得较大的传热极限值,而垂直顶部加热则对应较小的传热极限值。
2.Adopting R123,water and alcohol as the working medium,the effect of inclination angle and liquid filling ratio on heat transfer performance of pulsating heat pipes(PHPs) were studied on the PHP test rig consisted of 40 elbows bent by fine copper tubes with inner diameter of 1 mm and 2 mm.在内径分别为1 mm和2 mm的细铜管弯曲而成的40弯头脉动热管试验装置上,采用R123、水和酒精为工作介质,研究了倾斜角及充液率对脉动热管传热性能的影响。
6)charge up充气,充液