带压,Aquifer英语短句,例句大全

带压,Aquifer
1)Aquifer[英]['?kw?f?(r)][美]['?kw?f?]带压
1.Application of Emergency Drainage System and Waterproof Gates in Aquifer Mine;带压矿井应急排水系统和防水闸门的应用

英文短句/例句

1.band compression of facsimile signal传真信号的频带压缩
2.power tubing tongs with rollover feature带压紧轮的动力油管钳
3.APPLICATION OF PRESSURE LEAKAGE PLUGGING TOOLS IN COMPRESSOR REPAIR带压堵漏工具在压缩机检修中的应用
4.A region of low barometric pressure.低压带气压低的地区
5.self-contained press带有液压泵的压制机
6.environmental stressor带来环境压力的因素
7.live ultrahigh tension power lines超高压线路带电作业
8.electrohydraulic coil lifter电动液压式带卷升降台
9.electric, belt, fluid, etc drive电力、皮带、液压等传动
10.helical spline type actuator带螺旋活塞杆的液压缸
11.pinch solenoid driver压带电磁线圈驱动器
12.wide-band voltage tunable oscillator宽带电压调谐振荡器
13.grassland roller drill带镇压轮的草地播种机
14.A band of low pressure is moving across the country.一个低压带正横越该国.
15.A band of low pressure be move across the country一个低压带正横越该国
16.full hydraulic crawler excavator全液压履带式挖掘机
17.full hydraulic crawler type dozer全液压履带式推土机
18.A depression usually brings bad weather.低气压通常带来坏天气。

相关短句/例句

temperate low belt温带低压带
3)floating control system with pressure带压浮动
4)snubbing service带压作业
1.Development of tubing coupling detector used in snubbing service;带压作业油管接箍探测仪的研制
2.The control technique of the system in snubbing service is the synthesis of on-off flexible seal system and automation control method by changing the sealing state frequently.带压作业开关柔性密封系统及其控制技术是将频繁切换密封状态的开关控制型柔性密封系统及其自动控制方法和技术的分析与综合。
5)mining under safe water pressure of aquifer带压开采
6)extrusion-belt挤压带
1.Aimed at Jetta steering knuckle,the technology of two forging steps in one heat was presented,which combined precision pre-forging by extrusion-belt obliterated extrusion with open finish-forging.以捷达轿车转向节为研究对象,制定了挤压带式可分凹模闭塞挤压精密预制坯和开式终锻成形相结合的“一火两锻”成形工艺。
2.Aiming at the obliterated extrusion forming with extrusion-belt of pre-forging part,the influences of punch geometry,extrusion-belt length,mould temperature and lubrication to forming technology were discussed by using DEFORM,then the technology parameters used in the forming were acquired.针对挤压带式闭塞挤压精密预制坯的成形过程,以DEFORM软件为工具,研究了冲头形状、挤压带长度、模具工作温度、润滑等条件对成形工艺的影响,确定了成形过程中需采用的工艺参数。
3.In this paper, a new precision forming technology is put forward, which combines pre-forging by separable cavity die extrusion-belt type obliterated extrusion with post-forging.针对轿车转向节这类复杂枝杈类锻件的成形,提出可分凹模挤压带式闭塞挤压预制坯和终锻相结合的精密成形新工艺,介绍了可分凹模闭塞挤压工艺研究的实验结果和数值模拟结果,提出的新工艺具有降低设备公称压力要求和材料利用率高的重要结论。