1)triaxial creep三轴蠕变
1.Analysis of de-noising based on wavelet transform in triaxial creep experiment of rock;基于小波变换的岩石三轴蠕变曲线消噪分析
2.Experimental study on triaxial creep properties of granite under high temperature高温作用下花岗岩三轴蠕变特征的实验研究
3.The creep test mainly contains triaxial creep test and one-way compression creep test.4时的三轴蠕变,其不能反映应力水平对堆石料蠕变特性的影响。
英文短句/例句
1.Triaxial creep characteristics and constitutive relation of gas-containing coal含瓦斯煤岩三轴蠕变特性及本构关系
2.Study on Triaxial Creep Mechanism and Creep Model of Mica-quartzose Schist at Dam Abutment of Heihe Reservoir黑河水库坝肩边坡云母石英片岩三轴蠕变机理及蠕变模型研究
3.Experimental study on triaxial creep properties of granite under high temperature高温作用下花岗岩三轴蠕变特征的实验研究
4.Investigation on triaxial creep claystone under pore pressure孔隙压力作用下泥岩三轴蠕变实验研究
5.Uniaxial Ratchetting and Creep of 316L Stainless Steel;316L不锈钢单轴棘轮与蠕变行为研究
6.Study on Creep Characteristic of Propeller Shaft in Especial Condition;特定环境下螺旋桨尾轴蠕变特性研究
7.Studies on measure for decreasing the creep of the vessel's propulsion shaft segment船舶推进轴段蠕变减缓应对措施研究
8.Research of multiaxial fatigue-creep life prediction for turbine blade涡轮叶片多轴低周疲劳/蠕变寿命研究
9.Creep property of undisturbed and reconstituted Japanese clay was presented based on drained triaxial compression tests.研究了黏土的未扰动和重塑土样在三轴排水剪切试验条件下的蠕变特性。
10.A Research on Numerical Simulation and Uniaxial Penetration Creep Text of Asphalt Pavement;沥青路面数值模拟及单轴贯入蠕变试验研究
11.Analysis on Bending and Creep Buckling of Symmetrically Viscoelastic Shallow Spherical Shell;粘弹性材料扁球壳轴对称弯曲和蠕变屈曲分析
12.The Research on the Static and Dynamic Creep Model of Asphalt Mixture under Uniaxial Pressure;单轴压力下沥青混合料静动态蠕变模型研究
13.Research on low cycle-multiaxial fatigue-creep life prediction at high temperature for turbine blade涡轮叶片高温多轴低周疲劳/蠕变寿命研究
14.Research on the Vertical Stiffness and the Creep of the Primary Spring橡胶轴箱弹簧垂向刚度及蠕变特性的研究
15.MODEL STUDY OF THREE-DIMENSIONAL GRANITE CREEP PROPERTIES UNDER HIGH TEMPERATURE高温三维应力下花岗岩三维蠕变的模型研究
16.Research on Numerical Simulation and Lifetime of High-temperature Components Creep Damage under Multiaxial Stress State;多轴应力状态下高温部件蠕变损伤的数值模拟及寿命研究
17.The Study of Creep Properties of Three Dimensional Braiding Preform Reinforced Resin Composites;树脂基三维编织复合材料蠕变性能研究
18.Triaxial creep model and its stability analysis of gas-containing coal含瓦斯煤岩三维蠕变模型与稳定性分析
相关短句/例句
triaxial creep testing apparatus三轴蠕变仪
1.Creep experiments were conducted using the triaxial creep testing apparatus with pressure sealed storehouse,and the least square method was used to parameters identification for creep equation under different pore water pressures.利用带有压力密封仓的三轴蠕变仪进行了不同孔隙水压力条件下软岩蠕变试验,通过最小二乘回归分析对蠕变方程进行了参数识别。
3)Three axis creep test三轴蠕变实验
4)triaxial creep test三轴蠕变试验
1.Authors have made triaxial creep tests with mudstone on the gravity lever type rock creep testing machine developed by themselves and provided with triaxial pressure cell.采用自行研制的重力杠杆式岩石蠕变试验机并配备三轴压力室，从而对泥岩进行了三轴蠕变试验。
2.Based on the triaxial creep test,the creep properties of the asphalt concrete core-wall which was settled in Maopingxi earth-rock dam of the Three Gorges Project were studied.基于三轴蠕变试验,对三峡工程茅坪溪土石坝心墙沥青混凝土材料的蠕变特性进行了研究。
3.Methods Through the triaxial creep test,the triaxial creep curves and isochorounous stress-strain curves have been obtained,then the creep characteristics of mica-quartzose schist have been obtained by analyzing the triaxial creep curves,and the isochrounous stress-strain characteristics of mica-quartzose schist have been obtained by analyzing the isochorounous stress-strain curves.方法通过三轴蠕变试验首先得到了云母石英片岩的蠕变曲线和应力应变等时曲线,然后对试验曲线进行分析得到云母石英片岩的蠕变特性和云母石英片岩的等时应力应变特性,最后拟合应力应变等时曲线,并分析时间和拟合公式中参数的关系,得出了蠕变经验公式。
5)triaxial creep experiment三轴蠕变试验
1.It is an important method for studying the rheological characteristics of rock to choose an appropriate rheological model and obtain the corresponding parameters based on the triaxial creep experiment of rock in lab.基于室内岩石三轴蠕变试验资料对岩石的流变本构模型及流变参数进行辨识,是研究岩石流变力学特性的重要手段。
6)creep rupture/stress triaxiality蠕变断裂/应力三轴性
延伸阅读
MasterCAM8.0在四轴、五轴铣床加工中的应用与技巧MasterCAM8.0新增加了多轴加工模块，但在实际加工应用中数控机床的控制器是不同的，在后置处理时，如果在MasterCAM8.0提供的后置处理文件夹Posts中找不到适合数控机床控制器的后置处理文件，或者经过编辑某通用后置处理文件后，仍不能得到与数控机床控制器相适应的后置处理文件，那么就无法将多轴加工模块得到的NCI文件转化成实际加工中可用的NC程序。 笔者在工作实践中，通过适当的转化使某些常用、典型的四轴、五轴加工在MasterCAM8.0上得以实现，并且成功后置处理成适合加工实际的四轴、五轴数控铣床控制器格式的NC程序。 一、四轴加工的应用 卫生巾切刀成型辊的数控加工主要是通过用平铣刀和锥度成型刀在XK-715M机床（带旋转轴的三坐标数控机床）上实现的。旋转轴上夹持的切刀成型辊相当于第四轴——A轴，刀具在圆柱体上走空间曲线，就得到刀刃的型面。 那么，如何建出这条卷在圆柱体上的空间曲线呢？ 首先，在MasterCAM8.0中，根据切刀理论刃口展开图画出不同刀具的中心轨迹展开图，这是二维曲线。 然后，利用主菜单的转换→卷筒→串连，用串连的方式选取刀具轨迹曲线→然后设定卷筒直径、旋转轴X及曲线放置在圆柱体上的位置→确认后再作出与卷筒直径同样大小的圆柱曲面，作为4轴曲线加工的导动曲面，将空间曲线以投影方式投到圆柱面上进行加工。 虽然同样是FANUC系统，但XK-715M机床和加工中心控制器的所使用的格式稍有区别，所以在用MasterCAM后处理产生NC程序之前需修改后置处理文件MPFAN.PST。 方法如下：进入文件→编辑→*.PST→找到系统默认的MPFAN.PST文件，先作备份，如另存为MPFAN-1.PST文件，然后打开，找到下面清单中的变量rot_ccw_pos : 1，将其改为rot_ccw_pos : 0，并存盘。 # Rotary Axis Settings # -------------------------- vmc : 1 #0 = Horizontal Machine, 1 = Vertical Mill rot_on_x : 1 #Default Rotary Axis Orientation, See ques. 164. #0 = Off, 1 = About X, 2 = About Y, 3 = About Z rot_ccw_pos : 1 #Axis signed dir, 0 = CW positive, 1 = CCW positive 之后，进入“NC管理”菜单→更改后置处理文件→选中MPFAN-1.PST文件，再对NCI文件进行后置处理，产生符合XK-715M机床的NC格式。 二、 五轴加工的应用 以在FIDIA系统的T20上加工双角度叉耳内外形为例，说明用MasterCAM8.0实现T20上带固定角度的五轴加工。
