1)diversion bottom outlet导流底孔
1.Formwork for top-section of diversion bottom outlets of Jinghong Dam;景洪大坝导流底孔顶部的模板设计与施工
2.Quality control supervision on metal structure installation of diversion bottom outlets;导流底孔金属结构安装工程监理质量控制
3.With their major functions of river diversion and closure in the 3rd construction phase and releasing flood in the initial cofferdam supported generation period, the diversion bottom outlets of the TGP are hardly seen in the world for their high water head, huge discharges and complex operation conditions.三峡工程导流底孔承担三期导、截流和围堰发电期泄洪任务,水头高、流量大、运行条件复杂,为国内外导流工程罕见。
英文短句/例句
1.Flow Surface Construction at the Bottom in No.2 Diversion Tunnel of Double Arch Dam of Xiaowan Hydropower Station小湾双曲拱坝2号导流底孔底板过流面施工
2.Model study and prototype application of diversion outlet design for Three Gorges project三峡工程导流底孔水力学研究与运用
3.Rapid Construction Scheme and Analysis of Backfill of Diversion Bottom Tunnel and Penstock Chute;导流底孔及钢管槽的快速施工方案与分析
4.Hoisting and Installation of the Arc Gate and Embedded Part of the No.1 Low Diversion Tunnel in the Xiaowan Hydropower Station小湾水电站1号导流底孔弧形工作门及埋件吊装
5.counterbore with guide有导柱的平底扩充孔钻
6.hole-conductor current access device穿孔导体电流存取器件
7.STUDY ON MEASUREMENT METHOD OF SMALL ORIFICE CONDUCTANCE USING GAS MICRO-FLOWMETER气体微流量计测量小孔流导方法研究
8.Resistance to flow may be high enough to cause microvoids and porosity.流动阻力可能太高,从而导致微孔和多孔。
9.Simulation and Experimental Study on Down-the-Hole Drilling Fluid Field of the Hollow DTH Hammer Reverse Circulation Coring and Sampling Technology;贯通式潜孔锤反循环取心(取样)钻进孔底流场模拟与实验研究
10.Cranial Drilling and Catheter Drainage in Treatment of Hypertensive Cerebral Hemorrhage in Basal Ganglia颅骨钻孔置管引流治疗基底节区高血压脑出血
11.Precise Machining Technology of Thin-Wall and "Deep-Hole" Inner-Conductor Chocke-Slot内导体薄壁“深孔”扼流槽精密加工技术
12.ANALYTICAL METHOD CALCULATION AND MONTE CARLO CALCULATION OF THE ORIFICE CONDUCTANCE小孔流导的理论计算与蒙特卡罗计算
13.Experimental study on desulfurization efficiency in spouted bed with spotting punch draft tube开孔导流管喷动床脱硫率的实验研究
14.Aseismatic Analysis and Optimization Design for Inlet of Diversion Tunnel;导流泄洪底洞进口段抗震及优化分析
15.tap(ping) drill螺丝孔钻,螺丝底孔钻
16.Study on Influence of Preparation Process on Characters of PPy Conducting Thin Film Deposited on Porous Substrate;制备工艺影响多孔基底上沉积PPy导电薄膜性能的研究
17.Selection of craniotomy and double-tube drainage in the treatment of hypertensive intracerebral hemorrhage in basal ganglia region基底节区高血压脑出血开瓣手术与双管钻孔引流术的对比研究
18.The Effect of the Inlet High Baffle with Holes in the T-shaped Tundish Pouring Area on the Melt FlowT型中包注流区高挡墙导流孔对钢水流动状态的影响
相关短句/例句
bottom diversion outlet导流底孔
1.Three dimension FEM is adopted in the stress analysis of a RCC gravity dam during the construction diversion period,which especially for clearing the stress distribution of the top area RCC concrete that under design RCC concrete age and around area of the large-scale bottom diversion outlet.采用三维有限元法对某碾压混凝土坝(RCC)在施工导流期的应力场进行分析,着重校核了顶部未到设计龄期的碾压混凝土和大型导流底孔周边的应力分布;并初步探讨了在多因素影响情况下,从开始施工到蓄水运行的坝体温度场、应力场的全过程仿真分析方法。
3)bottom outlet diversion底孔导流
4)TGP diversion bottom outlet三峡导流底孔
1.Research on flow-induced vibration and its control for radial gate of TGP diversion bottom outlets;三峡导流底孔弧形闸门泄洪振动与控制研究
5)diversion outlet closuring导流底孔封堵
6)arrangements of diversion bottom outlets导流底孔布置
延伸阅读
导流筒分子式:CAS号:性质:安装在搅拌釜内的构件。用它来控制返回流的速度和方向,以使被搅拌物系中确立某一特定的流型。对于螺旋桨搅拌器,导流筒套在叶轮的外面;对于涡轮搅拌器,导流筒置于叶轮的上方。在大型矿浆浸出槽中,用置于导流筒中的叶轮代替气流搅拌,可使能耗降低,并缩短了操作周期。