1)blind-hole method盲孔法
1.Analysis and experimental study on identification of inner force of steel tube under tension(compression) and bending using blind-hole method盲孔法识别拉(压)弯钢管内力的分析与试验
2.In order know the size and the distribution of residual stresses of mill welding seam,this paper uses blind-hole method to test the girth welds between round plate and the cylinder body of the mill produced by CBMI CONSTRUCTION CO.为了了解滑履磨机焊缝残余应力的大小和分布规律,该文应用盲孔法对中材建设有限公司生产的某型号磨机的圆平板与圆筒体之间的环焊缝及其近缝区的表面残余应力进行了现场测试。
3.To enhance the measurement accuracy for welding residual stress in the converter,the traditional blind-hole method is improved by widening hole and increasing depth more than once after drilling hole on one measuring point.为提高炉体焊接残余应力测试精度,对传统的盲孔法进行改进,即在测点打孔后多次扩孔并增加孔深;通过对SM400ZL钢焊接残余应力测试时的应变释放系数A,B进行实验标定,得出多组应变释放系数值,计算可得残余应力的估算值,并对不同状况下的残余应力值进行比较。
英文短句/例句
1.Application of Blind Hole Method and Impact Indentation Method in Residual Stress Measurement of Runner of Xiaowan Hydropower Station盲孔法及压痕法在小湾水电站中的应用
2.Research on Measuring Welding Residual Stress of Plate of Moderate Thickness Using Blind-hole Method;中厚板焊接残余应力测试的盲孔法研究
3.Analysis and experimental study on identification of inner force of steel tube under tension(compression) and bending using blind-hole method盲孔法识别拉(压)弯钢管内力的分析与试验
4.Experimental Study and Analysis of Stress Measurement of Circular Steel Tubes by Using Blind-Hole Method盲孔法测量圆钢管表面应力的试验与分析
5.Examination and Study on non-penetrating Hole Method Used for Stress in Steel Structure盲孔法检测钢结构构件应力的试验研究
6.Numerical Simulation Research of Blind Hole Method Testing Stress of Steel Structure Member盲孔法检测钢结构构件应力的数值模拟研究
7.Sticking Technology of Resistance Strain Gauge in Determining Test of Residual Stress by the Blind-hole Technique盲孔法残余应力测试中的电阻应变片粘贴技术
8.Research of Numerical Calculating Method for Elastic Release Coefficients in Blind Hole;盲孔法中弹性阶段释放系数的数值计算方法研究
9.Application of Improved Blind Hole Method to Welded Iron Tower Joint for Stress Relieving with Heat Aging改进型盲孔法在铁塔焊接接头热时效消除应力中的应用
10.Black of the card盲孔(纹板上无孔的部分)
11.This paper briefly intro-duced the practice of longhole blast shaft-formirg method for blind shaft sinking in Tongshan Copper Mine.本文简要介绍了深孔爆破成井法在铜山铜矿盲竖井掘进中的实践。
12.Micro-via Filling and Through Hole Plating in one Process in Vertical Line垂直电镀线盲孔和通孔同步电镀工艺
13.Study on the Physical and Mechanical Performance of Back Covered Porous Brick and Its Masonry;盲孔多孔砖及其砌体物理力学性能的试验研究
14.Blind-hole lower bushing prevents leakage."盲孔"下部衬垫能够防止泄漏。
15.Finishing Technology of Large Diameter Blind Holes in Hydraulic Oil Tank Case液压油箱壳体大盲孔的光整加工技术
16.Replace length cut springs to std. springs. Close blind holes.将定尺弹簧改成标准弹簧.关闭盲孔.
17.FEM simulation of blind bolt connection based on ANSYS基于ANSYS的盲孔螺栓联接的有限元仿真
18.An experimental study of drilling small and deep blind holes with an abrasive water jet磨料水射流钻削深小盲孔的试验研究
相关短句/例句
Blind hole method盲孔法
1.In present paper,the relationship between blind hole method and Kirsch elastic solution is discussed on the basis of solution of 3D.通过三维弹性有限元分析和单向标定实验，分析了盲孔法与通孔解的关系，着重研究了应变释放系数Ａ、Ｂ值，Ａ、Ｂ值随着孔深与孔径之比（ｈ／ｄ）的增大而增大，当ｈ／ｄ＞１。
2.Phase-shift moiré interference method and blind hole method were used to measure the residual stress of composite materials.本文应用相移云纹干涉法与盲孔法相结合检测纤维增强复合材料的残余应力。
3.For checking the effect of runner welding and annealing of Xiaowan Hydropower Station, the residual stresses of runner before and after annealing are measured by using blind hole method and impact indentation method.为检查小湾水电站转轮焊接、退火效果,采用了盲孔法及压痕法对转轮退火前后的残余应力进行了测试。
3)blind-hole drilling method盲孔法
1.The initial residual stress of the polymer bonded explosive based on TATB and its distribution were tested by blind-hole drilling method.以TATB基高聚物粘结炸药(PBX)为对象,采用盲孔法测定了PBX炸药的初始残余应力及其分布,研究了孔深和钻孔后应变读数时间对结果的影响,以及样品热处理后对残余应力松弛的影响。
2.8 mm drill collar box connection from two manufacturers was measured by using blind-hole drilling method.采用盲孔法测量直径为158。
4)Mathar Soete drilling钻盲孔法
1.Distributions of residual welding stress and effect of post weld heat treatment (PWHT) on residual welding stress relaxation in Lehigh weld specimens was studied by Mathar Soete drilling.通过钻盲孔法研究了里海型焊接试板焊接残余应力的分布和焊后热处理对焊接残余应力松弛的影响 ,讨论了适合生产实际的焊后热处理条件。
5)testing method of superficial pits表面盲孔测试法
6)incremental-step blind hole drilling method逐层盲孔钻削法
延伸阅读
扎盲盲1.捉迷藏。
