近液相线,near-liquidus英语短句,例句大全

近液相线,near-liquidus
1)near-liquidus近液相线
1.The as-cast microstructure of ZL201 alloy prepared by near-liquidus electromagnetic casting(NLEMC)was studied by means of electron microscope and image analyzer,and the mechanical properties of the alloy parts thixoformed were given through tests.采用电子显微镜、图像分析仪、维氏硬度计及电子拉伸机,研究了ZL201合金近液相线电磁铸造(NLEMC)的铸态显微组织,进行了触变成形实验,测试了成形件的力学性能。

英文短句/例句

1.Preparation of a New High Strength and Heat Resistant GW103K Magnesium Alloy Semi-solid Slurry by Near Liquidus Method高强耐热镁合金GW103K近液相线制浆工艺
2.Analysis on Microstructure of AlSi7Cu5 Alloy Obtained by Slope-liquidus MethodAlSi7Cu5合金斜板近液相线铸造组织分析
3.Effect of Pouring Disturbance on Preparation of Semi-Solid AlSi9Mg Alloy by Near Liquidus Casting浇注扰动对近液相线铸造半固态AlSi9Mg合金的影响
4.Study on the microstructure of Al-Mg-Si-Cu alloy semi-continuously cast near liquidusAl-Mg-Si-Cu合金近液相线半连续铸造组织研究
5.Effect of In-situ Al_2O_3 Particles on Microstructure of Aluminum Alloy by Near-liquidus Casting原位Al_2O_3颗粒对近液相线铸造铝合金组织的影响
6.On the Microstructure and Refining Mechanism of ZL201 Alloy Prepared by Near-Liquidus Casting in Electromagnetic Field电磁场作用中近液相线铸造ZL201合金的组织及其机理
7.Microstructure of Near-liquidus Semi-continuously Casting 6061 Aluminum Alloy工艺条件对6061铝合金近液相线铸造微观组织的影响
8.Al_2O_3p/Al-Cu matrix composites produced by in-situ reactive near-liquidus casting采用原位反应近液相线铸造法制备Al_2O_3p/Al-Cu基复合材料
9.Effect of In-situ Al_2O_3 Particles on Reheating Microstructure of Near-liquidus Casting Al-Cu Alloy原位Al_2O_3颗粒对近液相线铸造Al-Cu合金二次加热组织的影响
10.7075-TiC Particles Composite Produced by In-situ Reactive Near-liquidus Casting原位反应近液相线铸造TiC_p/7075铝基复合材料的制备
11.The axial droplet velocity profile is nearly linear across the pipe section, and is different from the axial gas velocity profile.液滴速度与气相速度分布不同，在垂直方向上液滴的轴向速度近乎呈线性分布。
12.A hyperbola approaches but does not meet its asymptote.双曲线逐渐接近它的渐近线但不相交。
13.It is observed that considerable liquation microcracks and some other microffissures called solid-state microcrack initiate in the regions nearby the fusion line and propagate across the grain boundary.研究发现，熔合线附近的热影响区产生大量液化裂纹和沿晶扩展的固相裂纹。
14.Curve-intersecting Poly-line Approximation and Compression of General Curves;一般曲线的相交折线逼近与数据压缩
15.The Development of On-line Liquid Near-infrared Spectroscopy Analysis System;在线型液体近红外光谱分析平台的开发
16.In-Line Monitoring of Core/Shell Emulsion Polymerization Using Near-Infrared Spectroscopy近红外在线监测技术用于核壳乳液聚合的研究
17.The right iliohpogastric nerves and umbilical spine line almost is a right angle.右髂腹下神经与脐—棘线相交近似垂直。
18.Asymptotic unitary similarity-preserving linear maps on B(H)B(H)上保持逼近酉相似的线性映射

相关短句/例句

near-liquidus casting近液相线铸造
1.Al_2O_3p/Al-Cu matrix composites produced by in-situ reactive near-liquidus casting采用原位反应近液相线铸造法制备Al_2O_3p/Al-Cu基复合材料
2.The near-liquidus casting process was used in casting AZ91D alloy, and its microstruc- ture was compared with that prepared by liquid casting.采用近液相线铸造的方法浇铸了镁合金ＡＺ９１Ｄ，并与液相铸造的组织进行了对比。
3.The microstructure evolution of AZ91D magnesium alloy SSM (semi-solid metal) ingots obtained by near-liquidus casting was investigated under altering partial remelting temperature and holding time.对近液相线铸造AZ91D镁合金半固态坯料进行部分重熔,通过改变部分重熔时的加热温度和保温时间来研究其微观组织的演化规律。
3)liquidus casting近液相线铸造
1.In this paper,the microstructural evolution of Al-Si alloys were simulated in mullti-scales during Liquidus Casting.本文对 Al-Si 合金近液相线铸造过程微观组织进行了模拟,建立了金属凝固过程组织演变的宏-微观耦合模型。
4)holding above the liquidus近液相线保温法
5)near liquidus casting近液相线铸造
1.The effects of stewing time and cooling capacity of mould on the cast structure of AZ91D alloy were investigated for near liquidus casting processing.研究了AZ91D镁合金在不同浇铸温度下组织的对比 ,以及稍低于液相线的近液相线铸造时静置时间和不同冷却能力铸模对铸态组织形貌的影响·结果表明 ,浇铸温度高于液相线时 ,降低浇铸温度有利于减轻镁合金的组织疏松 ,但组织粗大 ,此趋势持续到液相线上沿 ;而在稍低于液相线浇铸时 ,组织明显细化 ,有蔷薇化趋势 ,不再有高于液相线铸造时的显微气孔·在稍低于液相线温度时 ,适当静置有利于组织细化 ,一定程度上的枝晶熔断促进了蔷薇化 ,但不显著 ,静置时间过长 ,晶粒又有长大趋势 ,且出现个别异常长大枝晶·冷却速率对铸造组织的影响与静置时间有相近规
6)Near-liquidus Casting近液相线铸造法
1.Status and Prospect of Semi-solid Formation Processby Near-liquidus Casting Method;近液相线铸造法半固态成形工艺的现状及发展前景