1)hardened steel淬硬钢
1.Numerical Control Machining Technology of Hardened Steel Based on HSM;基于HSM的淬硬钢数控加工技术
2.Experimental Study on Dry Turning of Hardened Steel with Ceramic Cutters;陶瓷刀具干式车削淬硬钢试验研究
3.Study on FE Simulation of Chip Formation and Temperature Field during High Speed Machining Hardened Steel;高速切削淬硬钢切屑形成过程及温度场有限元模拟研究
英文短句/例句
1.surface hardening steel低淬透性钢, 浅淬硬钢, 表面硬化钢
2.Study on Cutting Temperature under Ultrasonic Hard Turning 45 Hardened Steel超声硬切削45淬硬钢的切削温度研究
3.A Comparison Study on Wet & Dry Cutting Hardened Steel with PCBN Cutting Tools;PCBN刀具干湿切削淬硬钢对比研究
4.Study on interrupted turning of hardened steels with PCBN toolsPCBN刀具断续车削淬硬钢的试验研究
5.Study on High Speed Cutting Hardened Steel with the Coated Insert (CN35);硬质合金涂层刀具（CN35）高速车削淬硬钢的研究
6.An Experimental Research on the Surface Roughness by Dry Cutting of Hardened Steel SKD11硬态干式车削淬硬钢SKD11表面粗糙度试验研究
7.Experimental Study on Surface Roughness of HSM Hardened Steel高速铣削淬硬钢表面粗糙度的试验研究
8.Research on Technology Parameter Optimization of High Speed Milling of Hardened Steel Mould;淬硬钢模具高速铣削工艺参数优化研究
9.Mechanism and Process in High Speed Milling Hardened Steel with Micro-End Mill;小直径铣刀高速铣削淬硬钢机理及工艺研究
10.Theory and Application of Finishing Turning 45 Hardened Steel;淬硬钢精切加工方法的理论与应用研究
11.Cryogenic Finishing 45 Hardened Steel by CNC Lathe;数控车床低温精切45淬硬钢的切削研究
12.Study on Microscopic Mechanism of Instability in the Primary Shear Zone during High Speed Machining Hardened Steel高速切削淬硬钢主剪切区微观失稳机理的研究
13.Study on Experiment of Ultrasonic Vibration Turning 45 Hardened Steel with PCBN ToolPCBN刀具超声振动切削45淬硬钢的试验研究
14.Simulation and Cutting Experiment of Hard Cutting under Air Cooling Cutting风冷条件下淬硬钢切削过程的仿真与试验
15.Study on Cutting Force for Milling Hardened Steel Arc Path with Micro-end Mill小直径铣刀铣削淬硬钢圆弧切削力研究
16.Can we control the hardness of the steel when it is harden?我们能够在钢淬火时控制它的硬度吗?
17.Turning of Hardened AISI 440C Stainless Steel with PCBN Tool淬硬AISI 440C不锈钢的车削加工
18.Influence of overlapping amount on hardness of 9Cr2 steel by laser hardening搭接量对激光淬火9Cr2钢硬度的影响
相关短句/例句
Quench steel淬硬钢
1.High speed milling quench steel Cr12MoV is studied.针对淬硬钢Cr12MoV进行了高速铣削研究,重点研究了铣削条件对刀具磨损的影响。
2.The high speed milling Cr12MoV quench steels of 50 HRC and 60 HRC hardness were tested with TiAlN coated tools.针对硬度分别为50 HRC和60 HRC的Cr12MoV淬硬钢材料,采用TiAlN涂层刀具进行了高速铣削试验,重点研究了铣削方式、刀具螺旋角以及润滑方式等铣削条件对刀具磨损的影响。
3)SKD11 hardened steelSKD11淬硬钢
4)water hardening steel水淬硬钢
5)Full-Hardened Steel全淬硬钢
6)oil hardened stee油淬硬钢
延伸阅读
硬下疳 硬下疳 为一期梅毒的临床特征。在大、小阴唇内侧或子宫颈部可见圆形或椭圆形硬结，表面糜烂，边缘稍隆起似软骨样硬，直径1～2cm，表面有浆液性分泌物，含有大量梅毒螺旋体，传染性很强，可伴单侧或双侧腹股沟淋巴结肿大。妊娠期子宫颈因脆软及充血而易受损伤，使梅毒螺旋体入侵致病。因而孕期硬下疳好发于子宫颈，一般在2～6周内自愈，故不易被发现。
