充填率,filling ratio英语短句,例句大全

充填率,filling ratio
1)filling ratio充填率
1.As a result,the manipulate conditions were determined of the steel ball medium filling ratio and original ratio,grinding production and concentration,and compared with the energy saving on several type mill.4m加长非标型球磨机的基本参数,确定了钢球充填率、原始配比、给矿速度、磨矿浓度等操作条件,并对耗能进行了对比,指出下一步应改进之处。
2)packing fraction充填率
1.Some concrete suggestions for increases of packing fraction and rotating speed are presented, the rotating speed is 11.提出增加充填率和加快转速的具体措施。
2.18 m×3 m ball mill with double chambers(the front chamber for steel shot and the rear for steel roll), overfall type, packing fraction of 35%～40% and productive capacity of 3 t/h phosphate rock was retrefitted into the one with double chambers, overfall type through grating, packing fraction of 55%～60% and productive capacity of 6 t/h.8m×3m双仓磨机处理磷矿石,按溢流磨机标准装填磨料时,进料仓装钢球,出料仓装钢棒,磨料综合充填率35%～40%,处理磷矿量3t/h左右。
3)media-filling rate填料填充率
1.The influence of air-water ratio,HRT(hydraulic retention time),media-filling rate for biological contact oxidation tank and dosage of flocculating agent,surface loading for flotation tank on pollutants removal was studied.开展了生物接触氧化/气浮工艺处理微污染源水的中试研究(规模为20 m3/h),考察了生物接触氧化池的气水比、水力停留时间、悬浮生物填料填充率和气浮池混凝剂投加量、表面负荷对污染物去除效果的影响。
4)Filling rate填充率
1.Under the condition of DO of 4 to 5 mg/L in HSMBR and HRT of 4 h,the COD removal rate is 75%,62% and 56% respectively when the carrier filling rate.在HSMBR中的溶解氧浓度为4～5mg/L、HRT为4h的条件下,当填料填充率分别为45%、20%和0时,系统对COD的去除率分别为75%、62%和56%;对NH3-N的去除率>90%;膜清洗周期分别为40、36和24d。
2.The elongation and filling rate have been selected and the tensional coefficient has been calibrated systematically on the bases of the rolling law.根据轧制规律,选用合理的延伸系数和填充率,系统地校核了张力系数,减少了断锭堆料事故,改善和提高了铝杆的力学性能,延长了轧辊使用寿命,降低了产品的制造成本。
3.In order to model the estimation for the over-sample and sub-pixel imaging considering the detector s filling rate,the detector pixel spread function is derived adversely by the sub-pixel arithmetic.针对探测器存在填充率时过采样和亚像元成像质量评价问题,利用亚像元算法反演线阵探测器像元扩散函数,发现较过采样成像不仅能在1/m微扫描作用下减小采样间隔,还能使探测器矩形窗口压缩m倍。

英文短句/例句

1.Calculation of Packing Fraction and Packing Efficiency of Optical Fiber Bundle光纤传光束敛集率及其填充率的计算
2.Research on the influence of packing fraction and rotation rate on the power of ball mill填充率与转速率对球磨机功率影响的研究
3.Preparation of SiO_2 ordered macroporous materials with high filling ratio高骨架填充率的SiO_2有序大孔材料的制备
4.Dependence of PDE Performance on Nozzle-shape and Fuel-filling Rate;喷管形状和燃料填充率对脉冲爆轰发动机的效能影响研究
5.Effect of Filling Rate on Treatment of Polluted River Water by the Combined A~2/O Process填充率对组合式A~2/O工艺处理某污染河水效果的影响
6.The influence of defect filling fraction on the energy band in 2D point defect phononic crystals二维点缺陷声子晶体中缺陷填充率对能带的影响
7.Study of producting sludge characterizations of moving bed biofilm reactor with different filling proportions不同填充率对移动床生物膜反应器的产泥性能影响研究
8.permeability of tunnel fill material炮眼充填材料的渗透率
9.Discussion about relation between the rate of supporting pit roof and supporting effect of backfilling mass坑采充填接顶率与充填体承载效果关系探讨
10.Discussion on Raising the Rate of Supporting Pit Roof关于提高充填接顶率的若干问题探讨
11.The plasty of cavity of auricular concha and mastoid obliteration can raise drying ear rate.耳甲腔成形和乳突腔骨膜瓣填充可增加干耳率。
12.Development and application of filling material for UHP EAF taphole超高功率电炉出钢口填充料的研制及应用
13.Study on RSA Modular Prime Number Theorem and Random Packed Probability Digital Signature;RSA模安全性及随机填充概率数字签名研究
14.Study of Thermal Conductivity of Natural Rubber Filled with Carbon Black炭黑填充天然橡胶复合材料热导率的研究
15.To fill plentifully, as with money or food.填充用钱或食物填满
16.To stuff, as for roasting.填充填料，可供烤炙
17.Analysis of filling effect and filling ratio of backfill mining in longwall face长壁工作面充填开采的充填比与充填效应分析
18.smaller scour-and-fill feature小型充刷-充填形态

相关短句/例句

packing fraction充填率
1.Some concrete suggestions for increases of packing fraction and rotating speed are presented, the rotating speed is 11.提出增加充填率和加快转速的具体措施。
2.18 m×3 m ball mill with double chambers(the front chamber for steel shot and the rear for steel roll), overfall type, packing fraction of 35%～40% and productive capacity of 3 t/h phosphate rock was retrefitted into the one with double chambers, overfall type through grating, packing fraction of 55%～60% and productive capacity of 6 t/h.8m×3m双仓磨机处理磷矿石,按溢流磨机标准装填磨料时,进料仓装钢球,出料仓装钢棒,磨料综合充填率35%～40%,处理磷矿量3t/h左右。
3)media-filling rate填料填充率
1.The influence of air-water ratio,HRT(hydraulic retention time),media-filling rate for biological contact oxidation tank and dosage of flocculating agent,surface loading for flotation tank on pollutants removal was studied.开展了生物接触氧化/气浮工艺处理微污染源水的中试研究(规模为20 m3/h),考察了生物接触氧化池的气水比、水力停留时间、悬浮生物填料填充率和气浮池混凝剂投加量、表面负荷对污染物去除效果的影响。
4)Filling rate填充率
1.Under the condition of DO of 4 to 5 mg/L in HSMBR and HRT of 4 h,the COD removal rate is 75%,62% and 56% respectively when the carrier filling rate.在HSMBR中的溶解氧浓度为4～5mg/L、HRT为4h的条件下,当填料填充率分别为45%、20%和0时,系统对COD的去除率分别为75%、62%和56%;对NH3-N的去除率>90%;膜清洗周期分别为40、36和24d。
2.The elongation and filling rate have been selected and the tensional coefficient has been calibrated systematically on the bases of the rolling law.根据轧制规律,选用合理的延伸系数和填充率,系统地校核了张力系数,减少了断锭堆料事故,改善和提高了铝杆的力学性能,延长了轧辊使用寿命,降低了产品的制造成本。
3.In order to model the estimation for the over-sample and sub-pixel imaging considering the detector s filling rate,the detector pixel spread function is derived adversely by the sub-pixel arithmetic.针对探测器存在填充率时过采样和亚像元成像质量评价问题,利用亚像元算法反演线阵探测器像元扩散函数,发现较过采样成像不仅能在1/m微扫描作用下减小采样间隔,还能使探测器矩形窗口压缩m倍。
5)Filling fraction填充率
1.Numerical result shows that the width of the lowest band gap increases (decreases) with increasing the filling fraction (lattice constant); The center frequency of the lowest gapwas about independent of the cylinder radius, but gets lower with increasing lattice constant.结果表明,当填充率(晶格常数)增大时,最低禁带宽度增大(减小);最低禁带中心频率基本不受散射体半径的影响,但随晶格常数的增大而降低。
2.There will be not only one gap in the photonic band structure in the case of incidence along the direction,it is shown that the middle frequency v of pseudo-gaps including the first gap and the third gap will increase when the filling fraction of the background dielectric medium inside the opal voids ff decreases, and that v will increase when the sintering factor.应用平面波展开法分析了三维反蛋白石结构光子晶体的带隙性质;计算了沿[111]方向入射时其赝带隙(第一、第三赝带)中心频率分别与填隙材料在模板中填充率ff、模板煅烧因子sf的关系曲线:随ff的减小,v增大;随sf的增大,v随之增大,非理想状态下,ff<100%、sf>1,因此较理想态发生蓝移;由此提出了求解平均填充率ffev与平均煅烧因子sfev的计算框图。
6)filling ratio填充率
1.Preparation of SiO_2 ordered macroporous materials with high filling ratio高骨架填充率的SiO_2有序大孔材料的制备
2.2% mixing moisture, 6r/min mixing drum rotating speed, 13% filling ratio,and 7min mixing time, it is ensured that the +3mm fraction in sintering mix over 85%.2 % ,混合机转速 6 r/m in,填充率 13% ,混合时间 7min时 ,即可保证混合料中大于3mm部分在 85 %以
3.For a single edgree of freedom(SDOF) non-obstructive particle damping(NOPD) system,the influences of factors such as particle filling ratio,particle material type,vibration direction and cavity shape etc on the structural damping characteristics are experimentally investigated.针对非阻塞性微颗粒阻尼(NOPD)单自由度体系,通过实验研究颗粒填充率、颗粒材料类型、振动方向以及空腔形状等因素对结构阻尼特性的影响,并根据实验数据对阻尼特性进行了拟合分析。