弯曲角度,bending angle英语短句,例句大全

弯曲角度,bending angle
1)bending angle弯曲角度
1.Based on the proposed model with known temperature distributions,the bending angle induced by the laser can be calculated.基于传统固体力学的平衡方程和相容性关系,同时考虑了板料激光成形中加热阶段的塑性变形和冷却过程的弹性变形,利用已有的激光扫描温度分布模型,建立了板料成形弯曲角度的解析模型。
2.Special incline is not usually main function plane of pressing, its external shape size and bending angle are not dimensioned directly in 2D part drawing;the data needs calculating.特殊斜面在冲压件中通常不是主要功用面,在二维零件图中,一般不会直接标注特殊斜面的外形尺寸及其弯曲角度,需要自行设法计算得到数据。
3.In the experiment it has been found that: when the thickness and length of the sheet metal is invariable, the bending angle increases with the sheet width increasing, and it tends to a fixed value when the sheet width is large enough.当板厚、板长一定时采用不同宽度的1Cr18Ni9Ti薄板进行等离子电弧弯曲成形的试验,试验发现:随着薄板宽度的增长,薄板弯曲角度增大,当板宽的增大到一定值时,薄板弯曲角度趋于定值。

英文短句/例句

1.Effect of bending angle on hydroforming of curved hollow components弯曲角度对弯曲轴线件内高压成形的影响分析
2.The temperature and the deformation fields of the forming process were calculated and the final bending angle was predicted.计算了弯曲成形过程的温度场及变形场，预测了钢板的最终弯曲角度。
3.Bent or angled like a hook.钩状的象钩子一样弯曲或成角度的
4.A short angled or curved line on a letter.字母弯曲之处字母上的曲线或带角度的短线
5.having or marked by bends or angles; not straight or aligned.有弯曲、角度或以此为特征；不是直的或成列的。
6.common Indian antelope with a dark back and spiral horns.印度普通的羚羊，角为深色并呈螺旋状象后弯曲。
7.The Bending of Isotropic Shellow Spherical Shell Supported by Corner Colums of Panels with Uniform Thickness;角点支承的等厚度各向同性球面扁壳的弯曲
8.Stochastic Variability Analysis of Bending Angle in Sheet Metal Laser Forming Process金属激光弯曲成形角度的随机变异性分析
9.The scales of Libra will hang awry until Aries props them up with its curving horns.天平座的刻度会歪曲地悬挂，直到白羊座用弯曲的角把它纠正。
10.Cut, threaded, and bends pipe to required angle, using pipe cutters, pipe-threading machine, and pipe bending machine.用切割器、螺纹机、曲器，针对要求的角度来切割、螺纹、弯曲水管。
11.cause to assume a crooked or angular form.引起弯曲或有角的形式。
12.The inner curve is angled correctly under the presser foot and is left flat凹的弯曲部位以正确的角度放在压脚下,并且放平。
13.As a consequence of this angular velocity, the field of the relative air flow past the airplane is curved.由于存在角速度，通过飞机的相对气流流场是弯曲的。
14.Having a horizontal surface without a slope, tilt, or curvature.水平的具有无倾斜度、倾斜角或弯曲的水平平面的
15.repeated bending stress strength反复弯曲疲劳强度极限
16.The beam has a constant flexural rigidity.该梁具有常数弯曲刚度。
17.Gentle bending, is put into use apply to curves and surfaces, or the corner, but many-sided.柔和弯曲,适用于曲线、曲面或角落，可多方面使用。
18.Bending behaviors of functionally gradient piezoelectric curved cantilever was studied.研究了弯曲型梯度功能压电悬臂梁的弯曲特性。

延伸阅读

弯曲工艺的概念及弯曲件1．弯曲工艺：是根据零件形状的需要，通过模具和压力机把毛坯弯成一定角度，一定形状工件的冲压工艺方法。 2．弯曲成形工艺在工业生产中的应用：应用相当广泛，如汽车上很多履盖件，小汽车的柜架构件，摩托车上把柄，脚支架，单车上的支架构件，把柄，小的如门扣，夹子（铁夹）等。　弯曲的基本原理：以V形板料弯曲件的弯曲变形为例进行说明。其过程为：　　　 1．凸模运动接触板料（毛坯）由于凸,凹模不同的接触点力作用而产生弯矩，在弯矩作用下发生弹性变形，产生弯曲。　　2．随着凸模继续下行，毛坯与凹模表面逐渐靠近接触，使弯曲半径及弯曲力臂均随之减少，毛坯与凹模接触点由凹模两肩移到凹模两斜面上。（塑变开始阶段）。　　3．随着凸模的继续下行，毛坯两端接触凸模斜面开始弯曲。（回弯曲阶段）。　　 4．压平阶段，随着凸凹模间的间隙不断变小，板料在凸凹模间被压平。　　5．校正阶段，当行程终了，对板料进行校正，使其圆角直边与凸模全部贴合而成所需的形状。　弯曲变形的特点：　　弯曲变形的特点是：板料在弯曲变形区内的曲率发生变化，即弯曲半径发生变化。从弯曲断面可划分为三个区：拉伸区、压缩区和中性层。